Forum Post: RE: DRV2603EVM-CT Requirements
Hello Brian,Thanks for your help. I have bought the DRV2603 and MSP430.However, I wondered how to connect the MSP430 to the DRV2603 module??many thanksxueqing
View ArticleForum Post: RE: TSC2046 communicating with a pic33EP256mu810
Dear Wendy,I want indeed the coordinates and not the temp or the aux. But if i look to fig 4 the mosi. so the master output to the tsc2046 I see 11011000 and that is the x measurement if i'm right. I...
View ArticleForum Post: touch screen
hiiii can any one tell me how the x-y coordinates select in any of the touch screen. i have one touch screen module that i want to interface with the MSP 2553. i connected the touch screen...
View ArticleForum Post: RE: Diode overwiew
Hi Ricardo,Welcome to the forum! You might try an internet search tool to find out more information. Here is one example of some available information:http://en.wikipedia.org/wiki/DiodeBest...
View ArticleForum Post: RE: LM96551
Ok, but (I have to make sure) to ensure the right work of all module, VPF and VNF inputs I should supply using only 100nF capacitors from VPP (VNN) signals? No additional elements or supply voltage...
View ArticleClik here to view.
Forum Post: NEED HELP ON AFE5801. I CAN NOT READ OUT REGISTERED SIGNALS FROM...
Hi all,I encountered some problems when testing the AFE5801. The chip is connected with the Xilinx V5- FPGA board using the SPI BUS. The digital signals writen into the SDATA port are:...
View ArticleForum Post: RE: TSC2046 communicating with a pic33EP256mu810
Hello Benjamin,Glad to hear your progress! The following is the C source code I used at TSC2046EVM (where I used the 24 Clock-per-Conversion method shown at Figure 9 pg15 of the d/s) for your reference...
View ArticleForum Post: RE: touch screen
Hello Satish,Are you using a TI's touch screen controller (TSC) device? If not, you may need to consult the manufacturer that produces the touch module.Regards,Wendy F.
View ArticleClik here to view.
Forum Post: RE: LM96551
The first chart is impedance from frequency, second the faze from frequency in transducer.Sorry for spam :)
View ArticleForum Post: RE: TMP441 soft reset
Jonas,I have discussed this with the design team. It will be helpful if you could provide us with the exact configuration that you have the device in.This includes:The voltage level you are using,pull...
View ArticleForum Post: TMP006 - fresnel to increase range?
Could a polypropylene fresnel lense be used with the TMP006 to increase range and possibly allow to be used for human presence-detection in a room?Thank you
View ArticleForum Post: RE: TSC2046 communicating with a pic33EP256mu810
Dear Wendy,It is working, but only with a pen and with my finger it is not accurate. the values are swinging. Can i improve the data i get form the controller? Something else the measurements are...
View ArticleForum Post: RE: TSC2046 communicating with a pic33EP256mu810
Hello Benjamin,Glad to hear your progress! The following is the C source code I used at TSC2046EVM (where I used the 24 Clock-per-Conversion method shown at Figure 9 pg15 of the d/s) for your reference...
View ArticleForum Post: AFE5804 LNA testing
hello,i am using AFE5804 EVM for Portable Ultrasound medical imaging.First thing i have to check the LNA CW output using Switch matrix.Please help me how initiate the registers using SPI.
View ArticleClik here to view.
Forum Post: RE: 4-20mA to 0-10v converter
Hello, Ramiro, this is Sandy. I'm from Sunyuan Technology: the professional and experienced designer and manufacturer of Power Modules since 2002.Products: Isolated DC-DC Converter, Signal Data...
View ArticleClik here to view.
Forum Post: RE: TMP441 soft reset
Hi Chris,Thanks for looking into this.VCC is 3.3V, which is applied ~1s before activity starts on the SMBus.Rise time of VCC is pretty much linear and monotonous and theramp time is about 5ms.The SMBus...
View ArticleClik here to view.
Forum Post: RE: LM96551
If you have problems with this chart also - try this link:http://andgasow.nazwa.pl/Obraz1.jpgThanks for help.Regards,Grzegorz
View ArticleForum Post: RE: TMP006 Sensing Distance
Ersan,The issue is size of the object versus distance. Without any optics involved, the recommendation is that the distance from the TMP006 be a maximum of 1/2 the diameter of the object being...
View ArticleForum Post: RE: NEED HELP ON AFE5801. I CAN NOT READ OUT REGISTERED SIGNALS...
Green James1,To read a register out of SDOUT:1.Enable Reg Readout @ 0[1]2.Write Dummy Data to your desired register, e.g. 21[XXXX]3.Enable Reg Readout @ 0[0] for future writes.See pg. 25 of datasheet...
View Article
