Forum Post: RE: AFE58JD32: AFE58JD32 output linerate issue
thank you Another issue is that we have set the system to 4 ADCS PERLANE mode, with a system clock of 80 MHz. Then the sampling frequency is 40 Msps. The total bandwidth in the 4-lane mode is 40(...
View ArticleForum Post: RE: AFE58JD32: AFE58JD32 output linerate issue
Fs = 80 MHz Fc = 40 MHz NO_ADC_PER_LAne = 4 Lane rate = FS* NO_ADC_PER_LANE* ADC_RES * 10/ 8 Lane rate = FC * 2 * NO_ADC_PER_LANE*12 * 10/ 8 Which is 40 MHz* 2* 4 *12* 10 /8 = 4.8 GBPS
View ArticleForum Post: RE: AFE58JD18EVM: LVDS 16x serial data rate data recovery
Demod ramp pattern includes channel ID also as MSB bits . This is the difference between normal ramp and demod ramp.
View ArticleForum Post: ADS1298: Too much noise in ECG data
Part Number: ADS1298 Tool/software: I achieved clean 12 lead ECG data on the ADS1298 (in-house developed board) with ECG data from a Contec MS400 patient simulator, but when trying to measure only...
View ArticleForum Post: RE: AFE5401-Q1: GUI question
Hi, I am curious about why do you need AFE5401 GUI. Can you please share the use case
View ArticleForum Post: ADS8688: .
Part Number: ADS8688 Tool/software: Subject: ADS8688 SPI Random/Garbage Values with Input Voltage on All 8 Channels Hello everyone, I'm currently working with an ADS8688 ADC and am encountering a...
View ArticleForum Post: RE: ADS8684: SCLK rising edge to SDO valid
Hi Tom "A slower SCLK will give more setup time (longer valid time)" Does this mean that if the SCLK period is longer as shown in the figure below, the valid time will be longer by the same amount as...
View ArticleForum Post: RE: ADC12DJ5200RFEVM: Error message on HSDC pro
Hi Rob, Thank you for updating the installer. I can choose "ADC12DJxx00RF_JMODE0". I was able to acquire waveforms in Single Channel, but JMODE of Dual Channel is not displayed and I cannot acquire. I...
View ArticleForum Post: ADS124S08EVM: ADS124S08
Part Number: ADS124S08EVM Other Parts Discussed in Thread: ADS124S06 , , ADS124S08 Tool/software: Hello .. Can I Connect ADS124S06 Hardware with ADS124S08EVM with SPI Interface Am using ADS124S08EVM...
View ArticleForum Post: RE: ADS131E08: Issue Utilizing the Full Range
Okay! Thank you for helping us root-cause this problem, Dale!
View ArticleForum Post: RE: ADS5282EVM: Request for HDL Code for ADS5282 FPGA Integration
Dear Sir, We are currently interfacing the ADS8282 ADC with the ZCU102 board. The ADC is clocked at 40āÆMHz, and we are applying a 10āÆMHz input signal to one of the ADC channels. However, after...
View ArticleForum Post: RE: DAC60096: Dac
Can you please help me for REF1 and REF2 connection with refout generating REF501251DGK without jumper
View ArticleForum Post: ADS131M08: Overall accuracy 4-20mA loop
Part Number: ADS131M08 Other Parts Discussed in Thread: OPA2992 , TPS7A20 , LP2985A Tool/software: Hi Ti-Team I have an additional question regarding my circuit with the ADS131M08. I tested everything...
View ArticleForum Post: RE: ADS8665: Unexpected 2.2V Voltage on ADS8665 AIN_P Pin
Hi Jacob, When you (basically) leave the input of most ADC's open, it is not uncommon to see some sort of DC level on the floating input. It is due to the nature of the switched capacitor sample/hold...
View ArticleForum Post: RE: ADS112C04: ADS112C04IPW
Hi Ramin Tavassoli, Yes, this makes sense. You cannot hold the ADC in RESET, or leave the RESET pin floating, and expect it to work -Bryan
View ArticleForum Post: ADC12DJ5200RF: ddc
Part Number: ADC12DJ5200RF Tool/software: Hi Team, I am using the adc12dj5200's ddc modeļ¼the adc's clock is 5.2GHz.I use jmode16 to reduce the sampling rate to 650MSPS.In FPGA,The jesd204b's...
View ArticleForum Post: RE: ADS804: AD9221 Alternative (Parallel Output)
Hello Conor, The newest alternative we have would be the ADS7047 . This is a 12-bit, single channel, differential input device, but it has SPI interface. If parallel is needed, we do have the ADS7882...
View ArticleForum Post: RE: AMC1035: Signal impedance, input impedance and settling time
OK - Thank you! I just wanted to point out the isolation aspect between the two parts. With the higher input impedance of the AMC1035, you are correct in that it maps up to voltage measurements at the...
View ArticleForum Post: RE: AFE4490: Ambient canceled Red and IR data returning zero from...
Hello Don, Due to lack of response, I will close this thread. Please let me know if you have any additional questions. Regards, Payton
View Article