Forum Post: RE: TLV990-13: specifications
Toshi, Thank you for your patience while we see what we can find for you.
View ArticleForum Post: TS3A4751 Supply voltage
Hi TI I would like to use TS3A4751 switch in a product, but i think the datasheet is a bit confusing regarding supply voltages. The maximum VCC is 4V in the datasheet but the recommended VCC is max...
View ArticleForum Post: RE: TLV990-13: specifications
Here is what I was given from the team: Linearity does not change as a function of PGA. However ADC output will be noisier as PGA gain increases: because at high gain any noise at the analog input will...
View ArticleForum Post: AMC1301 Pspice model
Hi guys , i need Pspice model for AMC1301 , there is only TINA-TI Spice Model . BR Itay
View ArticleForum Post: RE: AMC1301 Pspice model
Hi Itay, Currently we only have the TINA model for the AMC1301 . I'll see what we can do to get a PSpice model as well.
View ArticleForum Post: Ultrasound Analog Front End With 204B interface
Dear Sir, Do you have Ultrasound Analog Front End With 204B interface product?
View ArticleForum Post: RE: Ultrasound Analog Front End With 204B interface
iehncent, Yes we have two AFEs (VCA +ADC): AFE58JD18 and AFE58JD16 and one ADC only part: ADS52J90 Chuck Smyth
View ArticleForum Post: RE: AMC1301 Pspice model
Hi Tom Tnx i will wait for the Pspice model from you.
View ArticleForum Post: Does TI has high common-mode voltage difference amplifier with...
hi, I am looking for an opamp to implement signal conditional circuit which has high common-mode input range 0 to 300V. it must allow variable gain from 1 to 10. Found the competitor part LT1990....
View ArticleForum Post: AFE5816: Frequency of ADC_CLK and FCLK
Hi all, According to the datasheet of AFE5816 , FCLK is the same frequency with ADC_CLK. However my customer reported that the FCLK is a half of ADC_CLK, and 12bit length of the data to be output are...
View ArticleForum Post: tlc5930
We now use tlc5930 for constant-current control. We need dot correction function but We are not sure about the control and timing of the chip . So hope to get help.
View ArticleForum Post: AF5809 Coefficient SPI Programming
Hi, I'm having trouble configuring the AFE5809 decimation filter. I'm using the following coefficients take from a previous post for say decimation by 8 filter uint8 pu8_fircoeff_DEC8[8 * 14]={...
View ArticleForum Post: ADS1220 using the SPI communication problem ( with PIC's MCU)
Hello: I use PIC's MCU (DSPIC30F5013) with ADS1220 connection ,using the SPI communication interface, I had a problem ,the number is not continuous (for example: a continuous voltage liter, 623 would...
View ArticleForum Post: RE: AFE5816: Frequency of ADC_CLK and FCLK
Toshi, Please ensure that ADC Reg 1 [2] and [4] are both set to '1'. Thanks, Chuck
View ArticleForum Post: RE: AMC1301 Pspice model
Hi Tom Any news about the pspice model ? Br Itay M
View ArticleForum Post: RE: AMC1301 Pspice model
Hi Itay, I'll try to get a timeline from the modeling team.
View ArticleForum Post: RE: Using LM98725
Hello Martin, This is a 3.3V part and the abs max voltage as shown in the datasheet is 4.2V, with current limited. Vih is 2V. I would recommend keeping the input voltages less than the supply voltage...
View ArticleForum Post: ADS131A04 Not Sending Expected Response
I'm following the Initialization Sequence in the Applications Section 10.4 of the Data Sheet. ( http://www.ti.com/product/ADS131A04/datasheet/ Everything is good up until I issue the UNLOCK command....
View ArticleForum Post: RE: LM98620 eval board schematic
Can Hooman or anyone else re-share the schematics for LM98620 evaluation board? Best regards.
View Article