Quantcast
Channel: Data converters
Browsing all 37651 articles
Browse latest View live
↧

Forum Post: Haptic touchscreens with piezo-sealing problem?

Hello, I've studied the TI solution where rubber grommets are used to isolate the front plate from the whole device for getting a haptic touch effect using piezoelectric actuators. Shortly, the metal...

View Article


Forum Post: TL431A Output noise

Hi, Please tell me where the value of the output noise of the TL431A is mentioned in the data sheet. Best regards, Seishin

View Article


Forum Post: RE: TL431A Output noise

Helo Seishin, We do not have the value of the output noise specified for the TL431A . Best, Michael

View Article

Forum Post: RE: Haptic touchscreens with piezo-sealing problem?

Hi Zorica, This reference design is to show how to get strong haptic effects with a piezo actuator. We are happy to support any questions related to the electrical components or DRV2667 driver;...

View Article

Forum Post: Looking for Ultrasound Transmit Pulser with +/- 900V output pulses

LM96550 has the output pulses with +/- 50V and 2A peak. Does anyone know if there is an Ultrasound Transmit Pulser chip to generate output pulses with +/- 900V? Thanks, Mark

View Article


Forum Post: LM98620 soft reset

Hello support team. Could you please support about soft reset of LM98620 . I do not understand difference in FSM reset to REG reset well in datasheet. What means "REG"? (register? regulator?) In...

View Article

Forum Post: RE: LM98620 soft reset

Higa, I'm moving your post to the correct forum.

View Article

Forum Post: RE: LM98620 soft reset

Hi Higa The Reset FSM bit resets the Finite State Machines inside the device but does not reset most user programmable configuration register values. The Reset Reg bit resets the Finite State Machines,...

View Article


Forum Post: RE: TX-SDK-V2 EVB: Wrong power supply Phoenix Connector

Hello, So sorry about you getting the wrong cable type! Please send me your contact address and information so that we can ship you the correct cable assembly ASAP. Here is my email address:...

View Article


Forum Post: why Tx beam former IC lm96570 registers act as circular shift...

I am configuring the lm96570 ic registers by using SPI protocol. After writing in all the registers, i read the value from each registers. If i am reading the same register again and again, it is...

View Article

Forum Post: RE: TX-SDK-V2 EVM Power problem at banana connector cable

Hello Subash, Your issue with the TX-SDK-V2 may be related to the LM96570 power supply sequencing. According to page 13 of the user's guide (copied below), the 3.3V supply should be powered up before...

View Article

Forum Post: RE: TX-SDK-V2 EVM Power problem at +1.8V pin

Please see the other related E2E post here: e2e.ti.com/.../539504 Regards, Hooman

View Article

Forum Post: RE: TX-SDK-V2 EVM Power problem at banana connector cable

I follow the power sequence order such as Vsub,3.3V and 1.8V order only.

View Article


Forum Post: RE: TX-SDK-V2 EVM Power problem at banana connector cable

Could you see this post e2e.ti.com/.../542675 It is an other issue related to registers of lm96570 IC

View Article

Forum Post: RE: TX-SDK-V2 EVM Power problem at banana connector cable

When i am measuring the voltage of 1.8V pin with respect to gnd pin, it always gives 1.4V. But when i am measuring the voltage with respect to power supply gnd pin, it shows 1.8V. Do you have any idea?

View Article


Forum Post: RE: Voxel Viewer installation in Ubutnu14.04 64 bit

What is your problem how to solve ??

View Article

Forum Post: RE: TL431A Output noise

Hi Michael, Thank you for your reply. All right. Best regards, Seishin

View Article


Forum Post: RE: TX-SDK-V2 EVM Power problem at banana connector cable

Hello, The only thing we can think of is if you have a large amount of current that is causing the voltage drop. What kind of current readings are you getting on your power supply? Are you sure the...

View Article

Forum Post: RE: why Tx beam former IC lm96570 registers act as circular shift...

Hello Subash, I've talked to the LM96570 designer and this part should not be doing sequential Read / Write, which I'm hearing you are observing? If you follow the datasheet Figure 4 timing diagram,...

View Article

Forum Post: TSC2007 POR issue

Hi, Having read the app report SBAA161–March 2009 Important Considerations to Assure a Safe POR, I've came up with a few questions. In Specifications Related to POR section on page 2, it says: The POR...

View Article
Browsing all 37651 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>