Forum Post: RE: Lay out files of TX-SDK-V2
Hello Parisa, I am moving your post to the correct forum.
View ArticleForum Post: Error 91 occured at Variant to data in TSW1400.lvib:Frame.vi...
Whan i press the initialize button on AFE5818 EVM GUI, the following error was shown at TSW1400 HSDC Pro GUI Which is shown as following lines and also i attached image file Error 91 occured at Variant...
View ArticleForum Post: RE: Lay out files of TX-SDK-V2
Hello Parisa, I tried to locate board design files to share with you, but I have not been able to locate any. May be I can answer specific questions you may have about the board? Please let me know....
View ArticleForum Post: RE: Lay out files of TX-SDK-V2
Hi Hooman, I didn't know how to answer the email to you. I have a lot of problem with board. Several times it blew up so I replaced three IC's. My project this board is used as transmitter. I need to...
View ArticleForum Post: AFE5808A VREF question
Hi there, We are using AFE5808A for medical ultrasound system. If we decide to use internal reference for ADC, how should we connect pin VREF_IN and REFP and REFM. Is it ok to float all three pins?...
View ArticleForum Post: LM98725 - thermal Problems
Hi everyone, we are currently developing an Application using 4 of the LM98725 . From our first tests we saw that the AFE is getting a bit hot. We measured TC 80°C (at the case) when running at...
View ArticleForum Post: DRV2700EVM software crashed
I've just got DRV2700EVM devboard, trying to connect it to computer. The Piezo Control Console crashed when I have selected device, press Connect and trying to run console after that, it is crashing,...
View ArticleForum Post: RE: Lay out files of TX-SDK-V2
Hi Parisa, Sorry about the troubles you've been going through. I will send you what I have if you provide an email address that I can use. Hopefully we can work through your issues. Regards, Hooman
View ArticleForum Post: RE: DRV2700EVM software crashed
Hi Serge, Can you please (1) copy/paste the entire error message and post it on a reply, and (2) update the firmware on the DRV2700EVM and check if the problem persist? Leo Rodriguez ARP - Haptics
View ArticleForum Post: RE: DRV2700EVM software crashed
I have noticed the MSP430 chip is kind of hot, hard to keep finger on it after 10 minutes. Have decided to send back to replace.
View ArticleForum Post: RE: DRV2700EVM software crashed
Sorry to hear that. Please keep us posted as soon as you get your replacement. Thanks. Leo Rodriguez ARP- Haptics
View ArticleForum Post: RE: DRV2700EVM software crashed
Hi Serge, We do not support Windows 10 currently.
View ArticleForum Post: RE: DRV2700EVM software crashed
We have tried on one PC with Windows 7 - the same problem. Also, it is not explaining why MSP430 is getting hot.
View ArticleForum Post: RE: DRV2700EVM software crashed
Yes, the MSP430 sound like a problem. Piezo control console should work properly on Windows 7. Let us know when you recieve the new EVM and we can work through the software problem if it persists.
View ArticleForum Post: RE: LM98725 - thermal Problems
Hi Christian, Please refer to the thermal modeling of the LM98725 attached: (Please visit the site to view this file) The model shows the top of the case being pretty close in temperature to the...
View ArticleForum Post: RE: Output impedance of TX-SDK-V2 and power supply board
Hi Hooman, Thank you so much for your response! Output impedance of LM96550 : it is definitely very good to know that LM96550 should be able to handle the low loads on the order of 50 Ohms. The...
View ArticleForum Post: RE: LM98725 - thermal Problems
Dear Hooman, This was exactly the information i was looking for! Let me really thank you for perfectly anserwing my question! We are using actually a 6Layer Board, but we are just using some few vias...
View ArticleForum Post: Are there any ways to faciliate the AFE5809 configurations?
Hi, TI experts: I am using the AFE5809 to design one project. I found there're lots of registers inside the datasheet. i found one tool named as AFE5809EVM GUI, while the prerequisite is the EVM board...
View ArticleForum Post: RE: LM98725 - thermal Problems
Dear Hooman, one last question maybe. In the simulation there is stated 0m/s airflow. So it is assumed that there is no additional airflow, or is it meant that there is no air convection, which will...
View ArticleForum Post: RE: LM98725 - thermal Problems
Hi Christian, You are welcome! The 0m/s air flow means no forced air (no fan). Natural convection. Regards, Hooman
View Article