Quantcast
Channel: Data converters
Browsing all 37571 articles
Browse latest View live

Forum Post: RE: TSC2004: Sense Voltage (SNSVDD) set to less than I/O Voltage...

Hello Victor, I'll be responding soon with further information. Best Regards Jose Luis Figueroa Application Engineer

View Article


Forum Post: RE: problem with TX-SDK-V2 kitX

OK Thanks, I hope than I will find solutions to our problem because the kit's price was 800 € and it worked 10minutes only... Thanks for your help Dominique

View Article


Forum Post: THS8200&THS8315

THS8200 &THS8315 had NRND, Please help check if there have the new P/N to replace The industrial customer will want use them in the new design, Could you help give some advise Thanks a lot

View Article

Forum Post: RE: TSC2004: Sense Voltage set to less than I/O Voltage

Hi Victor It is always recommended to follow the given guidelines in the datasheet, if you don't follow them we don't guarantee optimal performance. In fact, it is recommended to connect I/OVDD, SNSVDD...

View Article

Forum Post: RE: TSC2004: Sense Voltage set to less than I/O Voltage

Hi Jose Luis, Could you please expand on the implications of this situation, in other words, we'd like to understand why is recommended that I/OVDD must be ≤ SNSVDD.

View Article


Forum Post: RE: LM9833: Compatibility with FR12F-J03 Canon contact image...

Jim, I was wondering if there were any example circuits or components list need to use the LM9833 . I want to be able to integrate the LM9833 into scanning a document and have it read by a linux...

View Article

Forum Post: RE: LM9833: Compatibility with FR12F-J03 Canon contact image...

Hi Isaac Support for this device is very limited. I am attaching all of the hardware and software (Windows 9x based) support information I am aware of. This information is provided as-is. This device...

View Article

Forum Post: RE: TSC2004: Sense Voltage set to less than I/O Voltage

Hi Victor, This condition could generate problems with the Power On Reset (POR). You can refer the following posts to find further information. e2e.ti.com/.../403463 e2e.ti.com/.../34756 Best Regards...

View Article


Forum Post: TSC2102: tr and tf

Part Number: TSC2102 Hi, I received the following question from my customer. The tr(Rise time) and the tf(Fall time) is not shown on the figure3. Could you show them on the figure3? Best Regards,...

View Article


Forum Post: RE: Using LM98725

Hello Hooman, I have tried to calibrate but results are still not so good. I'm confused to understand the settings for Black Target and White Target because I want to set black target value around 3200...

View Article

Forum Post: RE: TSC2102: tr and tf

Hi Kuramochi-san These parameters are the rise time(tr) and fall time(tf) of the BCLK signal. As it is shown in the SPI Timing Diagram Figure with the SCLK signal, it would be the same with BCKL...

View Article

Forum Post: LM98725 PLL Unlock

Dear. experts I'm using LM98725 on MFP scanner. I have few question about it. 1. When I start MFP and LM98725 , sometimes the PLL don't get locked. But if I restart MFP, it works well. Have you ever...

View Article

Forum Post: TSC2046EVM-PDK: TSC2046EVM-PDK software installation

Part Number: TSC2046EVM-PDK On a windows 10 machine, I am installing the eval software and the NI VISA from the supplied CD. After installation, I launch the TSC2046 program with the EVM connected...

View Article


Forum Post: RE: TSC2046EVM-PDK: TSC2046EVM-PDK software installation

Hello Daniel, Welcome to E2E, thanks for your interest in our products. Unfortunately, TSC2046 isn't supported by Windows 10. But Windows 7 or lower versions should be able to support this device. Best...

View Article

Forum Post: DRV2605: DRV2605 Issue

Part Number: DRV2605 Dear Sir, Pls help the issue for we founded that there is no overdrive or brake after measuring output signal of DRV2605 . The picture in below is measured signal from a 300ms long...

View Article


Forum Post: RE: DRV2605: DRV2605 Issue

Hi Ian, I'm not able to see the txt file with the register settings. For overdrive to be possible, the OD Clamp (0x17) need to be set higher than the rated voltage (0x16). Also the voltage supply needs...

View Article

Forum Post: TX-SDK-V1: Question about power supply

Part Number: TX-SDK-V1 From the Evaluation Kit Users Guide of TX-SDK-V1 the power up sequence that should be followed is: VSUB, +3.3V, +1.8V, ±5V and finally ±10V and ±50V (power down in reverse...

View Article


Forum Post: Using a Piezo Driver for a Doorbell Chime

Hi team, We are interesting in being able to play a user selected sound inside the house when someone rings a doorbell. Would a Piezo Driver, such as the DRV2700 , be good for such an application?...

View Article

Forum Post: RE: Using a Piezo Driver for a Doorbell Chime

Hi Akash, The DRV2700 could be suitable for this type of application using a piezo sounder. Look at the TIDU994a reference design for a similar application. The LM48560 could also be applicable.

View Article

Forum Post: RE: Interface AFE5808 with TSW1405

Is there any update on this topic? We are trying to integrate AFE5808 and TSW1405. We cannot find the device in drop down. It will be great if you can provide the ini file for the same. Also, what...

View Article
Browsing all 37571 articles
Browse latest View live