Forum Post: RE: [TSC2007] Sample program source request
Hi Jose, do you mean the TSC2007 GUI for windows7, if so, we would like to provide it to customer to see if this GUI enough for them or not? So, please send to me for support customer. Thanks. Regards,...
View ArticleForum Post: RE: [TSC2007] Sample program source request
Hi Jose, Today, we have tried to install the TSC2007 EVM software, but it seems the procedure missed the driver install, so we failed to launch the EVM GUI. Attached is the error messages pop up on the...
View ArticleForum Post: RE: [TSC2007] Sample program source request
Hi Arthur, Attached the GUI for Windows 7. Please let me know if this one works. (Please visit the site to view this file) Best Regards José Luis Figueroa Application Engineer
View ArticleForum Post: RE: DRV2624: DRV2624: Example code for waveform effects
Hi Davide, Are you using Haptic Control Console (HCC) and the DRV2624EVM for evaluation? I recommend using the RAM Manager in HCC for loading waveforms. There is not an example library due to...
View ArticleForum Post: RE: DRV2700: How to Select DRV2700 EVM Options to Support 30uF Load?
Hi Wayne, The DRV2700EVM can drive up to 100Vp, 200Vpp - differentially, across the outputs. The DRV2700EVM-HV500 can drive up to 500Vp on a single ended output. For each EVM, the output capacitance...
View ArticleForum Post: RE: DRV2665: Can DRV2665 drive Murata piezo PKM13EPYH4000-A0...
Hello Poh, As the boost voltage decreases, the frequency bandwidth increases. For this piezo sounder, you only need the boost to be set to ~20V. At a boost voltage of 20V, you should be able to easily...
View ArticleForum Post: RE: [TSC2007] Sample program source request
Hi Jose, I downloaded it from the link and installed it. But the same problem happen as attached messages. Please help. On the other hand, even if we solve this GUI problem, but what customer need is...
View ArticleForum Post: RE: DRV2700: How to Select DRV2700 EVM Options to Support 30uF Load?
Hello Kelly, Thank you for your advise. Can we use 4 pcs piezo in series to make 0.93uF equivlent capacitance 0.93uF? How long to charge to 480V for the DRV2700-HV mode? If the answer is negative,...
View ArticleForum Post: DRV2605L: Problem with sequencer
Part Number: DRV2605L Hi, I am having problems with sequencer. It seems it only plays first three samples and then stops, or if there is pause between effects, they are incorrectly played. Motors are...
View ArticleForum Post: RE: DRV2605L: Problem with sequencer
Hi Sasa, Is this in Haptic Control Console? Can you provide a screen shot of how you have the console window set up?
View ArticleForum Post: RE: DRV2605L: Problem with sequencer
Hi Kelly, No, it is not on haptic control console. We have bult pcb with processor and drv2605l for our device. Best regards
View ArticleForum Post: RE: DRV2700: How to Select DRV2700 EVM Options to Support 30uF Load?
Hi Wayne, Driving this capacitance to 480V would take ~0.5s. The flyback design is meant to drive <200nF capacitance. My suggestion would be to use multiple DRV2700 drivers for each piezo element.
View ArticleForum Post: RE: LM98620 eval board schematic
Hi, Can anyone please help. Regards Prasanna
View ArticleForum Post: Linux/TSC2008: Sample program source request
Part Number: TSC2008 Tool/software: Linux I can't do download TSC2008 Linux Example Driver in this url. www.ti.com/.../TSC2008-LINUX-DRV Best Regards Koji Bahei
View ArticleForum Post: RE: DRV2605L: Problem with sequencer
If it is of any help, this is what I'm sending over I2C: Basically sequence is Strong click 100%, then three times pause of 320ms, and again Strong click 100%. What I'm getting is: I'm getting one...
View ArticleForum Post: RE: Linux/TSC2008: Sample program source request
Hello, Welcome to E2E, thanks for your interest in our products. Attached the Linux Example Driver for this device. (Please visit the site to view this file) Best Regards José Luis Figueroa Application...
View ArticleForum Post: RE: LM98640: LM98640 ESD pulse
Hi Matthieu, I apologize for the delay in my response. I am moving your post to the Imaging AFE forum where the device is currently being supported.
View ArticleForum Post: RE: Linux/TSC2008: Sample program source request
Hello Jose, Thank you for your support. Best Regards, K. Bahei
View ArticleForum Post: TX-SDK-V2: Pattern length issue(LM96570 of TX-SKD-V2)
Part Number: TX-SDK-V2 Hi Im a graduate school student in Korea. I have a problem with the pattern length of tx-sdk-v2 . I am conducting research related to ultrasound stimulation. So we are examining...
View ArticleForum Post: RE: DRV2605L: Problem with sequencer
Even if I put only pause as sequence effect, there is short buzz sent to motor. Seems as this short buzz is appended to every effect in sequence. Does anyone have any idea? Best regards
View Article