Forum Post: RE: Tsc2007
Hello Raquib, AUX is an analog input pin and can be grounded if not used. If you would like to use AUX to measure an analog input, send the command with [C3~C0] =0010b, refer to table 3. What exactly...
View ArticleForum Post: RE: LM95234 address help
Hi Amy, There is no suffix to differentiate the slave address marking on LM95234 device. Any device exists on the SMBus protocol has a unique address (slave address). The LM95234 operates as a slave on...
View ArticleForum Post: RE: LM96550 (or 96551) pulsar
Evgeniy, The instantaneous current for each channel clamps at 2A. This means that you can run 8 channels at 50V simultaneously. The specs in the data sheet do expect a 2kohm load however. So 50/50 is...
View ArticleForum Post: RE: AFE5805 or LM96511
Valeri, For the TX810, I can recommend the TPS79633DCQR. Thanks, Chuck Smyth
View ArticleClik here to view.
Forum Post: RE: TMP513 I2C Code Example
Andres, I would like to also provide visually my process that I have written above.Please note that I am counting clock pulses and looking at the corresponding data that is written and read. If the...
View ArticleForum Post: RE: TSC2046E reading problem
Hello Unal, For noise problem, there are several spots to checkup, refer to the application report sbaa155a. Also double check the schematic could be helpful too. Just checked your code provided in...
View ArticleForum Post: RE: AFE5808EVM GUI for Windows 7
I have found the solution. We can basically let windows do the work for us. To install CDM drivers for an FTDI device under Windows 7, follow the instructions below: If no suitable driver is...
View ArticleForum Post: RE: lmp91050 dev board
Hello Bob, Apologize for the delay. I have a few questions: 1) What is the magnitude and frequency of the noise on the output of the LMP91050? 2) What is the configuration register contents of the...
View ArticleForum Post: RE: AFE0064 linearity
Hi, I managed to have the linearity up to full scale increasing the delay SHR to SHS up to 100us, then it works fine. unfortunately I cannot reduce V1 due to the interface to the ADC. I hope that will...
View ArticleForum Post: mixed signal
am an engineering student.........which is the best material from ti to learn analog mixing......??
View ArticleForum Post: question about AFE5805 schematic
Hi, I am designing a ultrasound device now. In AFE5805 datasheet, it says that the pin VCA_CS# (H4) can be connected to pin RST(H5). Does this means these two pins can be connected directly? In...
View ArticleForum Post: RE: LMP91200MT pH Sensor
Domenico, Your answer was extreamly helpful. Thank you so much!! Best Regards,
View ArticleForum Post: RE: TI-89 Failing
Hi Alexander, I'm sorry to hear about the issues you have your calculators! I bought mine a couple of years ago and it still works perfectly (and it still get's used quite a bit...) In this forum we...
View ArticleForum Post: RE: INT- Looking reference to build LMP91000 AFE EVM
Hi Xavier, the gae sensor holders are the following : manufacturer :Wearnes Cambion part number :450-3326-01-03-00 regards, Domenico
View ArticleForum Post: NEED INFORMATION- LM50CIM3/NOPB
Hi Can you please provide the following information for the PTN0805E6811BST1 Part ? 1. Junction Temperature Max (Tj Max) 2. Typical Power dissipation (Pd typ) 3. Maximum Power dissipation (Pd max) 4....
View ArticleForum Post: RE: TSC2007 I2C hangup
Hello Gaurav, 1. Is it possible because the SCL stretching requirement is not met? Refer to the attachment for the explanation and suggestion. 2. TSC2007 does not ACK the setup command 0xB0, as listed...
View ArticleForum Post: TSW1400EVM with AFE5805EVM
Hello, can I use the TSW1400EVM with the AFE5805EVM? Thanks, Gunter
View ArticleForum Post: RE: TWS1250EVM & AFE5805EVM - parallel data on header
Gunter, The data is simultaneously doing both. You can send two channels to the CMOS output headers. At the same time, you can capture one channel in the FIFO to send to the PC. This should work for...
View ArticleForum Post: RE: question about AFE5805 schematic
Lutao, I understand your frustration because that confuses me as well. In ramp mode, all channels are outputting a ramp signal and in normal mode you probably have connected only one input and...
View Article