Forum Post: RE: How to obtain the full datasheet and specification for the...
Hi Brian,thank you very much. What about the DRV2667 IC datasheet? I found only the preview one on the website.regards,Jacopo
View ArticleForum Post: RE: Can't get readings and PENIRQ getting down with ADS7843
[quote user="Wendy Fang"]I checked our EVM firmware, where it is: return (((pen_msb & 0x7F) << 8) + pen_lsb) >> 3;[/quote]Hi Wendy, when you mentioned EVM firmware, which EVM are you...
View ArticleForum Post: RE: TSC2046 interfacing with launchpad
I just fixed my problem of usng ads7843, a earlier version of tsc2046.My experience is: try to find an evm board which uses tcs2046 and download the bsp/bsl for that evm.tcs2046 is used in omap3530...
View ArticleForum Post: RE: What is Thermocouple Signal Power Level?
Thats OK. But I am interested in power level of thermocouple signal . That is Thermocouple is generating voltage, What maximum amount of current it can delivered to laod?
View ArticleForum Post: RE: AFE5809EVM ON BOARD CLOCK @ 8MHz in CW mode?
Hi Enrico,please find the answer below:-1. Can we have the output I / Q (on J12 / J13) of a single channel (only J1 for example) instead of all mixed together?No you can't. Using more channels at the...
View ArticleForum Post: Driver for Brushed DC motor-DRV8301?
My customer is designing with a brushed DC motor.According to the customer, the power rating on the motor is given as 0.3 Horsepower. This is a simple 2-wire motor and runs at a voltage of 12V. Based...
View ArticleForum Post: RE: minimum voltage/power to VPF (8,53 pin) and VNF (10,51 pin )...
Hi Samir,Just put between VPP/VPF and VNN/VNF 470nF/100V capacitors. Nothing else you should do.Best Regards,Mariusz
View ArticleForum Post: RE: Need Help for Ultrasonic Imaging Applications of...
Hi Shiwei,Q1: The TOD variance on various LM96570 chips could be up to 15.5ns and it's unknown and unpredictible. It's ABSOLUTELY unusable in >8 channel applications. Not worth a single penny.Best...
View ArticleForum Post: RE: DRV2604EVM-CT source code
I haven't found either. Let me know if you find it.
View ArticleForum Post: RE: What is Thermocouple Signal Power Level?
Hello Vishal,Current values depend on the specification limits of the Thermocouple manufacturer depending on the load thats being driven. We only manufacture Silicon based local and remote temp...
View ArticleForum Post: DRV8662EVM source code question
Downloaded the DRV8662EVM Source Code (sloc285.zip) file from the DRV8662EVM product page, and it expanded to a DRV8662EVM_RevD folder. Looks like the code is configured for the IAR MSP430 IDE, not...
View ArticleForum Post: RE: TMP100−EP Registers selection
Hi,Thanks for immediate reply.But TMP100−EP device do not had ALERT pin as like for the device TMP101−EP.So how ALERTs shall be transmitted by TMP100−EP.?once again i am mentioning my first question...
View ArticleForum Post: How to use CCSv5.2 for showing a existing image
For instance, if there is a image named 01.bmp , how can I use the CCSV5.2 to read it and show it?Thanks for your attention to this matter.
View ArticleForum Post: LM2907 pin description
I have a customer trying to part number the LM2907. They cannot create the part number unless the datasheet has pin descriptions. Please see the comments below fromt he customer:We are trying to set...
View ArticleForum Post: RE: DRV8662EVM source code question
Hi Mike,When I converted similar programs from IAR to CCS in the past, all I had to do to make it compile in CCS was to modify the LPMx exit call inside the ISR. For example, if you see:...
View ArticleForum Post: RE: TMP100−EP Registers selection
hi,Thanks Abhi. I have got the answer.Regards,Ashok
View ArticleClik here to view.
Forum Post: RE: LMP91200 pH sensor - Analog only?
Hi, David. I've the same problem. When I use MSP430F2013 as 16-bit ADC and MSP430F5509 as USB-bridge (see attachment), SPI programming options do operates only when all chips ere fed with power of 3.3...
View ArticleForum Post: RE: DRV8662EVM question re use of JTAG2SBW jumper board
OK, partial answer is found on the Touch Wiki, a schematic for the JTAG board...
View ArticleForum Post: RE: About conversion of tmp006's voltage
Hello Jary,Thanks for posting your TMP006 question in the e2e forums. There could be many factors involved in not being able to attain a stable voltage for about 30 seconds. It could be that your setup...
View ArticleClik here to view.
Forum Post: RE: DRV8662EVM question re use of JTAG2SBW jumper board
Mike, Sorry for any confusion. To connect the board:Connect the MSP-FET430UIF tool using the ribbon cable to the MSP-JTAG2SBW board.Then connect J2 on the MSP-JTAG2SBW to the SBW connector on the EVM....
View Article
