Forum Post: TS3A44159 as a RS232 demux
Hello,I am writing because I want to ask if in your expert opinion there could be any problem in using a TS3A44159 as a RS232 demux, in my application I only have one RS232 port but I need to connect 2...
View ArticleForum Post: What will be the response for the command 0xA4 (to measure the...
Hi I am interfacing TSC2046 controller with beagleboard XM with McSPI on module 3 and channel 0.Thank You.
View ArticleForum Post: RE: Thermal ressponcse of LMT87-Q1
Toshio-san,It is difficult for us to measure response time in air - so I'm not sure how successful we would be. It is much easier for us to send you information for stirred oil. We would be happy to...
View ArticleForum Post: RE: Damaged AFE5808 in Evaluation Module
Hi,Actually I am working on Tx_sdk_v1 evm. For that +/- 50v dc power supply required, So I generated +/- 50v from auto transformer and bridge rectifier with capacitive filter But pulser IC got...
View ArticleForum Post: RE: DRV8662_Maximum voltage_varying for frequencies
Hi Karun,The bandwidth of the system is dependent of the gain, which means that as you increase your frequency, you will observe a decrease in amplitude. for the 40 dB gain setting (mode 8), the...
View ArticleForum Post: RE: need help on 16 channel US pulser
Thank you charlesIf i share same supply (-50V) for both VSUB and VNN then how can i follow the power up sequence.?As in TX_SDK_V1 user guide it is mentioned that power up sequence should start with...
View ArticleForum Post: RE: got damage at pulser IC in Tx_sdk_v1
Hi,Actually I am working on Tx_sdk_v1 evm. For that +/- 50v dc power supply required, So I generated +/- 50v from auto transformer and bridge rectifier with capacitive filter But pulser IC got...
View ArticleForum Post: RE: DRV8662_Maximum voltage_varying for frequencies
Hi Mandy,Thank you for your response. The capacitance of my piezo actuator is only 25.7nF (well below the 50 nF) which shouldn't cause the problem. Is there a gain bandwidth product for DRV8662? How do...
View ArticleForum Post: ERRORS IN TSC
Hi All, I am using customized am335x_sk , i have just initialized the touchscreen. But it throws me some errors. In my board setting the LCD display is in the daughter board. The distance...
View ArticleForum Post: RE: Thermal ressponcse of LMT87-Q1
Hello Emmy-san,Thank you for your quick response.I am asking customer if stirred oil is OK for their requirement and I will inform you the results.Could you explain how to change the temperature in an...
View ArticleForum Post: TCA9548A as an audio switch
Hi I would like to use the TCA9548A as an audio switch, I need to make a 64 way monitor using I2C. Audio quality does not have to be very good. Can this be done?, Has this been done before using this...
View ArticleForum Post: RE: need help on 16 channel US pulser
Thanks charlesI will follow the sequence which you specified and get back to you
View ArticleForum Post: RE: TMP112 I2C communication
Hello Sebastian,Glad to know that you are able to communicate with TMP112 and Thanks for posting ypur findings in forums.There is no need to send the address pointer as long as the host know which...
View ArticleClik here to view.
Forum Post: RE: difference between diode connected transistor and grounded...
Hello Chris,My apologies for not being able to answer your question earlier. I would recommend using the diode configuration (Collector and Base shorted) in your application, primarily because of 2...
View ArticleForum Post: Programmable Current Source LT3092
we like to find replacement part of LT3092EST. is there any p2p or similar part? Very thanks.Info.Customer: DeltaApplication: Industrial Motor
View ArticleClik here to view.
Forum Post: Continuous Wave (CW) mode with TX-SDK-V1/NOPB
Hi, I am wondering about the continuous wave mode available on the evaluation module with the LM96570 and LM96551 chips:1) the National Semiconductor software that comes with the kit (NSC Ultrasound...
View ArticleForum Post: TSC2046 can support boot automatically RTP detection function?
Hi,TSC2046 can supports"boot automaticallydothe RTPdetection andmatchingthe impedance ofthe action" function?Thank you~
View ArticleForum Post: RE: DRV8662_Maximum voltage_varying for frequencies
Hi Karun,I am attaching the frequency response of the DRV8662 amplifier. However, the real bandwidth will be limited by the internal boost performance, which will depend on the load, inductor selection...
View ArticleForum Post: TMP006EVM software occasionally outputs 0 valued object voltage...
I am experiencing a strange but consistent bug with the TMP006EVM GUI: the software occasionally ouputs target object voltage readings of 0. It seems to only happen when the target object temperature...
View ArticleForum Post: RE: TMP006 on flexi?
Hello Arman,We are in the process of designing and validating a Flexi PCB board circuit for TMP006. Our temp sensors team is currently engaged in other higher priority tasks but, I will post a detailed...
View Article