Forum Post: RE: AFE4300 Impedance Measurement protection
Thanks for that info Praveen.Does TI recommend a particular ESD Diode part number, since I presume it needs to have a low capacitance value otherwise this will affect the Bioimpedance measurement?Chris
View ArticleForum Post: RE: capacitors in single polarity split rail supplies
Anish,In the context of my answer, a "good" battery is one that is nearly new or fully charged. A "bad" battery would be one that is old, nearly expended or needs recharging. A "good" battery has a...
View ArticleClik here to view.
Forum Post: RE: TMP006 Accuracy at cold
Arthur,I concur with you that the user guide document doesn't mention Tdie/Tambient has to be kept at a constant temperature in order to get a correct S0 slope. For a given Tdie/Tambient temperature...
View ArticleForum Post: TMP006
Can some one help me with the information as to how tmp006 is constructed and created?
View ArticleForum Post: RE: AFE4300 Impedance Measurement protection
Chris,We recommend TPD1E10B06 ESD diode.
View ArticleForum Post: RE: Inquiry regarding quiescent current on TMP112
Hello, thank you for your reply.Based on your comment, please let us clarify regarding each items below;Q1.> Therefore Iq(Average) =( (26ms*40uA) + (99mms*2.2uA))/125mS = 10.062uA=> Is it...
View ArticleForum Post: RE: TMP006
Hello Ganesh,Can you please be more specific on what exactly you are looking for. Are you interested in the setup of TMP006 or are you interested in the principle behind device operation?Regards,Abhi
View ArticleForum Post: RE: Inquiry regarding quiescent current on TMP112
Question: Is it possible for this device to transit into shut down mode without waiting 99ms, after issued the command from CPU and CPU has completed reading temperature data?Yes, it is possible to...
View ArticleForum Post: RE: LM81 heating up
Hi Adrian,I haven't heard this issue before. Could you please provide me the schematic? Thanks.Aaron
View ArticleForum Post: AFE5809 CW and TGC paths
I am new of the forum and I am studying the datasheet of AFE5809 in view of a possible application for parallel MRI. I have the following questions.Would it be possible to operate the CW and TGC paths...
View ArticleClik here to view.
Forum Post: About the software of AFE5809EVM.
Although AFE5809EVM is examined, starting of software does not go well.Since a specification & situation is carried out below, if a cause is known, please let me...
View ArticleForum Post: RE: LM95235 use with single ended diode
Here is a previous E2E post that shows how to connect the sensor when D- is connected to GND: http://e2e.ti.com/support/other_analog/temperature_sensors/f/243/p/146976/534047.aspx#534047 .
View ArticleForum Post: Interfacing OPT101 with ADC
Hi all, I am trying to interface OPT101 for measuring ambient light in terms of lux.....Now what Vcc shall I put? I am interfacing it to an ADC of MCU. Can I go upto 30 volts and use an extra opamp to...
View ArticleForum Post: RE: Time of Flight Chipset, OPT8140 / OPT8130, VSP5324 and OPT9110
Erwin,I have replied to your email to close this thread.
View ArticleForum Post: RE: LM95235 use with single ended diode
Further application details and the processor specifics: The chip in this application is the Vitesse VSC7432. The cathode side is internally connected to VSS in the device. Looking for an I2C...
View ArticleForum Post: RE: LM95235 use with single ended diode
Hello,You can use any of our TMP4XX devices (TMP431,TMP411,TMP432 etc) with remote channel configuration and have it working by using the above configuration. Measuring internal IC temperature by using...
View ArticleForum Post: RE: About the software of AFE5809EVM.
Satoshi-san,I tried to reproduce your issue in the Lab but I wasn't able to get those errors.Could you please uninstall the AFE5809GUI, TSW1250 GUI and any TUSB3410 driver installed?Then please refer...
View ArticleForum Post: RE: Interfacing OPT101 with ADC
my plan is...OPT101 to Scale down Opamp then to ADC with 5v ref then to MCU for PWM control then to LED driver and to LEDs. I am using internal 1M resistance which is closest...I may use external less...
View ArticleForum Post: Haptics Forum Migration
The Haptics customer base is growing and as we are getting into more applications like smartphones, tablets, automotive and industrial markets we have our own new forum now!It is under Amplifiers...
View ArticleClik here to view.
Forum Post: help in using pulser IC(lm96550) to generate +/-15v pulses
Hi, I designed Pulser IC (LM96550) board by taking the reference of Tx_SDk_V1 schematic. Intialized the Pulser IC with power on sequence ( EN=ground(low), MODE= LOW, VSUB=-20v, VLL(logic...
View Article