Forum Post: RE: TMP300 active
Hello Max,If you set the temperature resistor Rtemp to a particular value, OUT will toggle only when temperature exceeds the set temperature setting. 0deg C in your case.OUT signal is open drain output...
View ArticleForum Post: RE: LM71 interface question
Hi Peter,Thank you for your inquiry. Should you provide 16 clocks or 32 clocks? It depends on what you want to do. Normally, reading the temperature data is only required 16 clocks, but when you want...
View ArticleForum Post: RE: Need information- LM92CIMX/NOPB
Hi Jayakumara,Sorry for the delay. The attached file is the information that you’re requested. Please let me know if you have further question.(Please visit the site to view this file)Aaron
View ArticleForum Post: 2 channel sine wave generation at 35 to 40V output voltage
Hi,Can you please help me in selecting an IC for 2 channel sine wave generation at 35 to 40V for frequency ranging from 20KHz to 40KHz. i have tried TI's range but couldn't locate suitable. if one IC...
View ArticleForum Post: RE: TMP006 first sample after power up
Hello,Thank you for your contributions which confirm our problem! The current solution is as follows: power up, waiting for four samples (microcontroller in sleep mode), read out the values and power...
View ArticleForum Post: RE: Unable to run SensorEval Application
Hi Sam,I will send you the instruction shortly. Just to let you know that we are currently re-spinning the EVMs to work with Window XP or later. May I ask what device you are using with SensorEval...
View ArticleForum Post: RE: Selecting LED and photodiode
Deepak,TI has several partner companies that make LEDs and photodiodes and that list of companies is available at http://www.ti.com/lsds/ti/analog/webench/partner-leds.page. I would try inquiring at...
View ArticleForum Post: RE: TMP006: local heating causes cooler readings error
Hello Will,To answer your questions...1. Yes please use foam/ insulation materials behind the TMP006 PCB in order to reduce the effect of air through duct acting as a noise source. This will allow the...
View ArticleForum Post: RE: LM73 Power supply ramp-up issue
Hi Madhuri,Based on the temperature you provided, it seems that you had a slow ramp rate; therefore, the registers wasn't properly loaded into the eeprom. A power-on-reset (POR) will occur at a certain...
View ArticleClik here to view.
Forum Post: RE: TMP006 field of view
Greg, The small metal cans are not commercially available. I designed some and had FotoFab make me some. The prototypes are flat and I have to bend them. See the pictures below. www.fotofab.com...
View ArticleForum Post: RE: LMP91200 issues
Hi Tim,it is not mentioned, we have assumed that since a pH measurement can have as result both positive and negative voltages, a device with a single supply configuration (without any charge pump...
View ArticleForum Post: RE: LM98714 INCLK min range
Hello Hooman. Thank you for reply. The min INCLK :5MHz understood. and thank you It teaches influence for 5MHz low-level. Best regard Ben from japn
View ArticleForum Post: RE: TMP006 Question
Hello Eddy,To answer your questions:A1: You can increase the distance by restricting TMP006's Field of view by using lenses etc. I would like to confirm the distance requirements, is 1.5 meters? What...
View ArticleForum Post: RE: LM95234 / IBIS model
Aaron-san,Thank you for the answer.I submitted it to our customer.Best Regards,Kato / Japan disty
View ArticleForum Post: TSC2004 AUX and Temp conversions when display is touched
Can the TSC2004 be commanded to perform AUX input or Temperature conversions while the touch screen has pressure on the panel? The Table 6 on page 11 of SLAA359 seems to imply that while the pressure...
View ArticleForum Post: RE: AFE5809 LNA
Ran,No, the AFE5809 cannot operate in differential input mode. INM must be tied to ground through an external capacitor.Thanks,Chuck Smyth
View ArticleForum Post: RE: TMP006 Sensitivity Problem
Hello Gokhan,Yes, typically S0 would vary from 5 to 7E-14 but its completely depended upon a particular application. For industrial application like yours I wouldn't be surprised if your S0 is 2E-14....
View ArticleForum Post: RE: TMP006 plus lens
Hello Leonard,We haven't tried measuring the PCB/Semiconductors with a lens setup. However, we have tried without using any lenses and were able to acheive ~1degreeC accuracy at a distance of 1cm from...
View ArticleForum Post: RE: TMP006 Question: About glass & human body
Hello Edward,Yes, I believe hair would influence the temperature results. Even though hair has high emissivity its temperature will be close to Ambient temperature unlike that of skin which regulates...
View Article