Forum Post: RE: Connecting inputs of TX810
Thanks Chuck for Your answer.I wanted inputs shorted together only. 8 outputs are connected simply to 8 inputs of AFE, same as in typical application. Doing so, I've got 1 common input for 8 TGC signal...
View ArticleForum Post: RE: TMP006 Sensing Distance
Hi there, I want to use the TMP006 to measure ground surface temp (water, soil, foilage) from a UAV flying at 60 - 120m (90 -180 ft.) altitude. Is that a feasible application or would the sensor be...
View ArticleForum Post: LM139 J square wave
Im working with LM139 and im trying to make a symmetric square wave with different amplitude of a sinus wave. If the sinus wave is under 1V i dont get a pure square signal. How can i fix this?
View ArticleForum Post: RE: TMP006 Sensing Distance
Hello Nilis,TMP006 is not a viable option for you application due to distance(60m), filed of view restrictions and variable target objects in the system(soil,water,etc). Thanks for looking into this...
View ArticleForum Post: RE: LMP91200 - VREF is changed
Hi Ratislav,I do not have an aquarium, but can you give to me some details on the electric and electronic stuff you have inside?Is there any chance that the water is grounded ? If so you will have...
View ArticleForum Post: LM35 Long Term Stability
HelloCan anyone please give info about long term stability of LM35? How many years it preserves its relaibility ? What is the accuracy change according to years ?Thanks
View ArticleForum Post: RE: LMP92064 Current Sense Range
Anyone has any idea about it? I need help!!
View ArticleForum Post: MIXER IC
Hi, I am Trang, from Viet Nam.I want to find a mixer, which can down convert frequency from 70MHz to 10MHz, bandwidth 5MHz.I tried to find, but all most of ICs I found have frequency range...
View ArticleForum Post: Range on Panel Resistance
This quetsion is from on touch panel vendor in China. Their customers usually require that the panel resistance should be like Rx-x =200 – 500 Ohms, Ry-y= 600 – 100Ohms. This vendor wants to know...
View ArticleForum Post: RE: LMP92064 Current Sense Range
Hello Ishaan,Could you include the schematic of your system?Particularly how do you have the REFC & REFG configured?It sounds like there might some short or additional pull down that is introduced...
View ArticleForum Post: ADC Speed
Dear Administrator we are working at a project using AFE5809. The datasheet ADC clock speed is between 10MHz and 65MHz.What would happen if the device is used at a speed between 6MHz and 8MHz. The...
View ArticleForum Post: RE: LMP91200 - VREF is changed
Hi Domenico,directly in the aquarium is only pH probe, temperature sensor, thermostat and plastic pipe for external filter. I kicked out from aquarium temperature sensor and termostat so from...
View ArticleForum Post: RE: Piezo Vibration sensor
Milan, I am not sure which Piezo sensor will give you the best results, but i did find some links that may help you once you find your energy harvesting...
View ArticleForum Post: RE: LM35 Long Term Stability
Hi Ozer,I'm sorry for the delay. I was a bit busy to respond the thread in a timely manner. Let me see if I can get the data for you.Aaron
View ArticleForum Post: RE: lm95172 with negative temperatures
Hi Bruce,I'm sorry for the delay. I will look into this, and get back to you soon.Aaron
View ArticleForum Post: RE: The question about LM98620
Hello Mr. Taichi,I've sent your response to you via your private email.Regards,Hooman
View ArticleForum Post: RE: TMP006
Abhi,Thanks for the response. Sorry, I got pulled to another project for a minute.Basically, I can't possibly get any closer than 15cm and 30cm is more like it.From what I've gathered, although I'd...
View ArticleClik here to view.
Forum Post: RE: TMP20 - Temperature Error Curves
Hello Abhi,I do understand that error will vary between an analog and digital out part. In this case, I'm talking about a specific analog out part (TMP20). I'm asking for information specific to this...
View ArticleClik here to view.
Forum Post: RE: LM35 Long Term Stability
Hi Ozer,The long term stability is in the datasheet on page 4.I found the reliability data link...
View ArticleForum Post: RE: TMP121 and TMP123 Calibration
Hi Ivan,There is no calibration needed for TMP121 and TMP123. Thanks for using the forums, let us know if you have any further questions. Best Regards, Mayrim VerdejoApplications Support | MHR Sensing...
View Article