Clik here to view.
Forum Post: TMP104 Temp error vs. temp chart
Hi, I am looking for TMP104 Temp error graph versus operation temp.I found this on the datasheet but It only shows -40 to 125 degreeI need extended chart in operating temp. range which is -55/150...
View ArticleForum Post: RE: functioning of LM 96570
Hi,I want to know the range of pulse repetition frequency that can be supported by LM96570. I mean, how much frequency signal supported at Tx_En pin.Thank you.
View ArticleForum Post: RE: regarding AFE 5809 evm with TSW1400
Hi Chandu,First, I just want to prove that the LPF is working. I misunderstood and thought you were using the AFE5809 EVM. Do you still have access the AFE inputs via SMA? If so, can we set the LPF...
View ArticleForum Post: RE: TMP104 Temp error vs. temp chart
Hello Khai,Operating temperature range for TMP104 is –40°C to +125°C whereas –55 to +150 °C is the temperatures for absolute max rating temperature range. Which means at this range the past will still...
View ArticleForum Post: RE: Speed of TMP006 skin temperature measurement.
Hello Q.WFresnel lens is a right approach to restrict the fild of view and increase the signal strength. We have obtained good results with Fresnel lens in the past but we haven't used it particularly...
View ArticleForum Post: RE: Availability for CCD TC285SPD-B0
Hi, chrisis this item TC285SPD-30 still offer by TI.as i was heard that it's OBSOLETE by your distributors.but from your answer, it's still available in 2013-10-24. pls let me know the...
View ArticleClik here to view.
Forum Post: RE: LMP92064 Current Sense Range
I use the exact same schematic as shown in the EVM manual for the sensor. The schematic is shown below. I'm trying to communicate the chip with an Arduino and it is able to rad the chip type as 7 which...
View ArticleForum Post: AFE5801 VGA
I need an 8 channel device where the VGA gain is totally independent from each channel. Unless I am missing something, the coarse and fine gain appears to apply to all 8 channels. A digital gain...
View ArticleForum Post: RE: Part no. for RF to Sma connector
Hi Fathima,I ask the original person who order the connector. Below is the email from him. I don't know if they change the part number or not. We went to SamTec's website, and the connector should be...
View ArticleForum Post: RE: LM98620: Analog input range and datasheet
Thx Hooman,I'll let you continue the thread with Sander and Koen if they have more questions over the topic.Thx again, nice weekend to allSergio
View ArticleForum Post: digital mili ohm simulator
Hi all,I want to make microcontroller based digital mili ohm simulator for RTD calibration, and other ohm simulation for process controls equipments.Kindly provide me the ideas for it. Thanking...
View ArticleForum Post: RE: Use LM35 to measure temperature of flowing gas
Hi Andrew,Could you please give several date and time? I will try to accommodate your schedule.Aaron
View ArticleForum Post: TEMP SENSOR
looking for simple temp sensor for 3 channel with I2C and 2 address. Are the TMP513 and TMP423 the right solution? Is the can the TMP175 also can be used?
View ArticleForum Post: RE: tmp441 --remote temperature error
Hi,we are looking into the issue you are facing. Can you please provide us additional details so we can help you? please provide the register contents for any register that you have written to, in...
View ArticleForum Post: RE: tmp441 --remote temperature error
hi,maybe i have solved the problemthank you all the same
View ArticleForum Post: RE: LMP92064 Current Sense Range
Hi Ishaan,Are you reading all the data registers in descending sequential order? (Address 0x203, 0x202, 0x201 and 0x200). All data registers must be read before new conversion data is available.Also, I...
View ArticleForum Post: RE: TEMP SENSOR
Hello Eli,Both TMP513 and TMP423 support 3 channel inputs. You can use 9 TMP432 and 4 TMP513 devices on an I2C bus. On the other hand TMP175 is a local temperature sensor where in you can connect upto...
View ArticleForum Post: RE: digital mili ohm simulator
Hello Pankaj,Unfortunately we may not be able to support you on this.This forum is intended for TI's silicon temperature sensors, please choose an appropriate forum. In the mean time, I will move yuor...
View ArticleForum Post: specification of LM96570
Hi,I want to know the range of pulse repetition frequency that can be supported by LM96570. I mean, how much frequency signal supported at Tx_En pin.please help me. Thank you.
View ArticleForum Post: RE: LMP91200 configure as pH measumement
Hi Mauricio,The LMP91200 contains only one 16 bits register, it's a configuration register and doesn't contain the value of the ph or temperature, please check page 19 of the datasheet for more details...
View Article