Forum Post: RE: Question of TMP421/3 remote device
Jacob, I am sending out a conference call for today 4PM Arizona time which I believe is 8am for you. We need to have a conference call sooner than previously proposed. I have just discussed this with...
View ArticleForum Post: RE: Pulse Patterns from TX-SDK-V2
Gunter, TX734 is not available. We have the TX517 but that is only 1-2 channels. LM96550 is the only 8-channel pulser available. What TX-SDK-V2 documents would you like to see?
View ArticleForum Post: RE: Some clarification on the output of the DRV2665
Hi Eric, Thanks a lot for your reply. So this means that the output voltage is dependent on the capacitance of the piezo actuator, am I correct? I obtained the info from the datasheet as attached, but...
View ArticleForum Post: RE: Some clarification on the output of the DRV2665
Hi Eric, My bad, I referred to the wrong datasheet. I must have clicked wrongly upon the request for it. On the other hand, if there are series capacitance with the piezo, wouldn't there be a voltage...
View ArticleForum Post: RE: Trouble with the DRV2603EVM-CT
Stuart, Thank you for your feedback, it is much appreciated. A couple of comments to help you find the sections in the User's Guide I have seen the same issue while programming the EVM. Typically it...
View ArticleForum Post: RE: TSC2046E linux device driver code.
Hello Wendy,Thanks for the reply.giridharakn@gmail.com is my email id. Please send me the source code.We are using the android kernel 3.0.15. Do we need tslib along with this driver to push the touch...
View ArticleForum Post: TMP006 dust in the environment?
Hallo,I am planing to use TMP006 to measure temperature in Power Electronic applications, inside Power Converters cooled by air flow.My concern is about the possibility of reducing sensibility due to...
View ArticleForum Post: TSC2007 X Y Line Min. Max. Input Capcitance
A customer of ours is using this chip for some TP's they have made by a competitor of ours - they believe the root cause of the failure is due to the amount of Capacitence on the touch panel itselfThe...
View ArticleForum Post: TMP275 ALERT sink current capabilities
The datasheet does not specify the max sink/source current capabilities of the ALERT pin.I would like to connect a LED to that pin, sinking 5mA. Can I do that for a few seconds?
View ArticleForum Post: RE: DRV8601 starting current capability
Hello,I am not the DRV8601 expert, but if you need more current than you may also be able to consider the DRV8837.
View ArticleForum Post: RE: TMP275 ALERT sink current capabilities
Jake,I am currently looking into this and will get back to you shorty.
View ArticleForum Post: RE: TMP006 dust in the environment?
Hello,I get small presentation from our design team on this topic. Basically, dust prevents signal from entering the sensor and causes a flat offset error which can be calibrated out if the dust level...
View ArticleForum Post: RE: medical grade/high accuracy infrared temperature sensor?
Hi Ron, DanielI am very interested in medical application of this sensor too. For a medical grade thermometer, the accuracy is 0.2 degree C, right? if TMP006 or next gen sensor can achieve this...
View ArticleForum Post: RE: TSC2046E linux device driver code.
Hello Giri,TSC2046 Linux driver will be on you way.Regards,Wendy F.
View ArticleForum Post: RE: TSC2007 X Y Line Min. Max. Input Capcitance
Hello John,Do you talking about the capacitance of a 4-wire resistive touch panel, right? We are not a touch panel manufacturer but rather design and produce the controllers for touch panels or touch...
View ArticleForum Post: RE: TSC2008 SPI timing
Hello John,TSC2008 has an internal oscillator, ranging around 3MHz to 4MHz under 8 bit resolution, or a half of that under 12 bit resolution. Refer to page 3 of the d/s.Thus, you do not need to clock...
View ArticleForum Post: RE: AFE5851 EVM & SP605
Hi Chuck,I was able to acquire with the TSW1250 using the MATLAB code. Now my problem is to acquire the external trigger from the same MATLAB code.Could you help me? Do you know anyone who could help...
View ArticleForum Post: RE: Some clarification on the output of the DRV2665
Hi Eric, What is your opinion? I'm not sure if the series capacitance enables the piezo to be driven at higher voltages, since there'll be a voltage division between the extra capacitor. The piezo...
View ArticleForum Post: RE: TMP006 dust in the environment?
Thanks Adrian,It was GREAT !!! Exactly the input I was looking for !!!Wail
View Article