Clik here to view.
Forum Post: RE: TMP007EVM software installation problem
User417230,Attached is the zip file information as I see it when I download the SBOC441.zip file. Also shown is the directory inside to open and the setup.exe file to run to install the GUI.I am...
View ArticleForum Post: RE: LM75x vs TMP75x
Hi Daniel-san,Thank you very much for your kind explanaation.I could understand well. I will recommend TMP75x to my customers from next time.Best Regards,
View ArticleClik here to view.
Forum Post: RE: About output capacitor (CL)and ripple noise of REF5025 &...
Satoshi,Figures 16 thru 21 in REF50xx PDS show line (power supply change) and load (output current change) transient response as seen at the output of REF50xx. Placing 1uF capacitor on TRIM/NR pin 5...
View ArticleForum Post: RE: Support Panel resistance spec. of TSC2046E
Dear Andy, Just one question. If we simply add a resistor (200ohm) over Y+ or Y- to compensate the impedance of Y plate. Has any problem for it? Thanks.BRPatrick
View ArticleForum Post: RE: LMP90100 GPIO healthiness check
HI...Still I am not able to find the mistake in LMP90100 side.Can you tell what are the initial register configuration settings required for GPIO.How can I find the error in LMP with oscilloscope, what...
View ArticleForum Post: RE: Body temperature sensor
Hi Alex,Yes, your ESD concerns are valid but this is something that can be addressed with on-board system components such as ferrite bead capacitors. You can perform a power-on ESD test to verify your...
View ArticleForum Post: RE: TMP112 Questions
Hi Alex,Please see my reply on:http://e2e.ti.com/support/other_analog/temperature_sensors/f/243/t/356577.aspxMayrim
View ArticleForum Post: RE: how to get emv kit data into matlab
Hi MayrimMy mail ID is kpradh2@uic.edu-Kartikey
View ArticleForum Post: RE: LM96194 AD_IN6/7 voltage sensing error
Hi Sachin,I will investaget this and get back to you.Take care,
View ArticleForum Post: RE: Variation in temperature measurement
Hi Jay,The LM92 measures temperature through its leads. The most accurate temperature reading is to place the heat source as close to the leads as possible.We do not have any driver code that...
View ArticleForum Post: RE: LMP90100 GPIO healthiness check
Hi Sravanthi,Were you able to read back the content of the registers you have programmed ?Until you are not able to do this I cannot help you.regards,Domenico
View ArticleForum Post: RE: Body temperature sensor
Alex,I haven't done this on the past. I will try to get some inputs from the power team. I will share any information I find. Mayrim
View ArticleForum Post: RE: Which is the dotted pin of LM94023 (DSBGA Package)
Hi Shibing,I will get back to you soon.-Michael Wong
View ArticleForum Post: RE: schematic with ADS7846
Your schematic is correct. If the LCD you are using is a bit noisy, adding several decoupling capacitors, from Y+, Y–, X+, and X– to ground, is a good way to reduce the analog input noise from the...
View ArticleForum Post: RE: Noise in PCB
Hello Santosh,Your question is hard to answer without seeing the actual layout. I will try to make a few observations based on the small amount of information provided;PCB related noise can be caused...
View ArticleForum Post: RE: touch pressure dependent X/Y measurements: TSC2046
Hello Wendy, I have a solution(s) to issue(s) I had with the TSC2046.1.) It seems the 1.5K ohm resistor and Schottky diode hysteresis circuit (described previously) is still necessary to prevent false...
View ArticleForum Post: RE: TS5A23166
This is from the person who originally posted the question. I have found the problem. It is not the IC.It was a soldering & board cleanliness problem. We were hand soldering this small IC to...
View ArticleForum Post: RE: Gain matching
Hello Wonni,Glad to hear you have successfully used the AFE5808 in your US application already. Having come from using the AFE5808, switching to the AFE5808A will be very easy. AFE5808A is an...
View ArticleForum Post: RE: About flick with TSC2046E
Hi Hirata-san,Sorry, I am not able to provide you with a MIPS example project. I suggest you port the C code from the Atmel project to your own project. I think you only have to complete the code for...
View Article