Forum Post: RE: TSC2007 I2C Address Configuration
Hi Andy Lui, We have done a series of testing in our board for evaluating the address switching issue, and our observation are listed below please check if these observations makes any sense...
View ArticleForum Post: RE: TSC2007 I2C Address Configuration
Did you measure the voltages on SCL and SDA, are they not greater than Vdd+0.3V and supplying the TSC? Using 2K2 pull-up resistors it looks like you have a long (capacitive) bus, did you try series...
View ArticleForum Post: RE: TSC2007 I2C Address Configuration
Hi Nithin, One of the most common issues on TSC2007 is the POR issue. TSC2007 has some requirements on the POR timing, which could be found on Page 31 of its datasheet. Based on your testing and...
View ArticleForum Post: RE: AFE58JD18 request
Kang, I've moved this post from the /etc...Data Converters Forum to the Imaging AFEs Forum. I'm not absolutely positive this is where the post belongs, since I see limited references to this part in...
View ArticleForum Post: RE: AFE58JD18 request
Thanks Joseph, Kang, you are correct, LVDS and Demodulator are featured in this device. Chuck Smyth
View ArticleForum Post: RE: Bit CLP mode enable for LM98725
Hello, Regarding your question on LM98725 CLP mode Enable: When enabled, Bit CLP mode closes the input clamp switch during the reference period of every pixel in the line. It is similar to what is...
View ArticleForum Post: RE: TSC2013 Knowledge
hi Andy. Do you have Reference Windows Driver for TSC2013-Q1 . Best Regard H.Ogawa.
View ArticleForum Post: RE: TSC2013 Knowledge
Hi Hiroyuki, No, we don't have the reference Windows driver for TSC2013-Q1 now. Instead, there is a reference Linux driver available. Here is its link...
View ArticleForum Post: RE: TSC2013 Knowledge
Hi Andy. Thanks for the information. Do you have any plans for release in the future. Best Regard. Hiroyuki Ogawa
View ArticleForum Post: RE: TSC2013 Knowledge
Hi Andy. Are you allowed to use the firmware contained in " TSC2013EVM ". The firmware is compatible with Specification of "Windows Touch"? Best Regard.
View ArticleForum Post: RE: Bit CLP mode enable for LM98725
Hello, Hooman! Thank you for your answer. Elnur.
View ArticleForum Post: RE: TSC2013 Knowledge
Hi Hiroyuki, Are you looking for the firmware for the TSC2013EVM . Here is link: e2e.ti.com/.../3140.reference-firmware-for-tsc2013-q1 This firmware is for demo purposes only and isn't compatible with...
View ArticleForum Post: board adapter
Hi. I have an AFE5851 EVM and I want to connect it to the TSW1400 EVM. Could you tell me what is the adapter's name and where to buy this adapter Regards Marcelo Márquez
View ArticleForum Post: TSC2013-Q1 power consumption
Dear Sir, TSC2013-Q1 datasheet mentioned that SNSVDD Supply current is about 350 mA at Vdd3V at figure 5 on page10. I assume the correct supply current is 350 uA. Is it right? Regards, Hiroaki
View ArticleForum Post: RE: TSC2013-Q1 power consumption
Hi Hiroaki, Yes, you are right. What you found should be some typos. Sorry for that. Andy
View ArticleForum Post: TSC2013EVM ISSUE
Hi All, I have bought TSC2013EVM for working on RESISTIVE TOUCH interface. the board is not powering up once I connect the USB cable & default switch selection on the DIP-SWITCH. kindly let me know...
View ArticleForum Post: RE: TSC2013EVM ISSUE
Hi Mahesh, Did you see the power-indicator LED (LED502) was on when this board was connected to your PC? Did you try using a multi-meter to make sure whether this board was actually powered on or not?...
View ArticleForum Post: RE: TSC2013EVM ISSUE
Hi Andy, Thanks for suggesting me to look into the Hardware & debug it, the LED502 was not glowing ON, so I went through schematic & found that F500 was not showing continuity, hence further...
View ArticleForum Post: RE: LM96550
Hi, I meet a problem about LM96550 and LM96551 : Can I replace LM96550 with LM96551 directly? I look at their datasheet, these two and pin to pin compatible. But I notice that LM96551 don't need +/-40...
View ArticleForum Post: RE: LM96550
Hi Yuan, Yes, you can replace the LM96550 with the LM96551 . In the LM96551 , you should connect put 10uF || 0.1uF bypass caps between VPP (pins 4-7 & 54-57) and VPF (pins 8 & 53). Similarly,...
View Article