Forum Post: DP83848I/ withstand voltage on MDI Terminals
Hello, When a noise occurs in MDI interface, How much withstanding voltage does DP83848I have on MDI terminals? Best Regards, Toshiki
View ArticleForum Post: RE: functioning of LM 96570
Dear Mariusz, I tried to download from here www20.zippyshare.com/.../file.html your SW for calculating the delays, but it isn't available anymore. May you please send me it to my email...
View ArticleForum Post: RE: functioning of LM 96570
Hi Mariusz, Would you please send me (saveriominutoli63@gmail.com) a copy of your app for calculating beamform? Thank you so much!
View ArticleForum Post: RE: UC1844J
I am not sure if you are just looking for help on the topside markings, but here is a link to that webpage that could be of help: www.ti.com/.../topsidemarkingformats.tsp
View ArticleForum Post: Any other device could replace LM1851, since its status show =>...
Dears, I'm search the device that can detect the leakage current in three phase AC Voltage application. Please kindly help on this request, thanks!
View ArticleForum Post: RE: UC1844J
Thanks, but I know this. Interesting marking is not front and on the back of the chip. What does it mean? Or taken from another chip?
View ArticleForum Post: RE: DP83848I/ withstand voltage on MDI Terminals
Hello, Does any of you have the answer? I would appreciate it very much if you could reply as soon as you can. Best regards, Toshiki
View ArticleForum Post: Regarding maximum duty ratio of PWM IC UC1824 or UC1524
Is it possible to generate more than 90% Duty ratio with PWM IC UC1824 and UC1524 in the temperature range from -25 degrees to +60 degrees Celsius? Is there any other space grade PWM IC for the above...
View ArticleForum Post: RE: functioning of LM 96570
Hi, The resource is no more accessible through zippyshare link. Can you please mail it to vennila.5432@gmail.com?
View ArticleForum Post: RE: functioning of LM 96570
Hi Mariusz, The zippyshare resource is no longer accessible. My project requires the delay software. Would you kindly send the software to vennila.5432@gmail.com?
View ArticleForum Post: IC for analog A-weight filter?
Hello, I am looking for IC solutions to implement an A-weight analog filter with minimal components and with the lowest noise possible. Suggestions on parts? https://en.wikipedia.org/wiki/A-weighting...
View ArticleForum Post: Supply voltages on LMP92064
I am studying the use of MLP92064 in my Design. I need to know if I can use differents voltages on the pins: VDD and VDIG. All examples I've seen use the same voltage on these pins. I must use 5V on...
View ArticleForum Post: RE: Any other device could replace LM1851, since its status show...
Dears, Any updated for this question?
View ArticleForum Post: RE: functioning of LM 96570
Here is the delay calculation software you had asked about which I got from one of the E2E posts a while back, and made by Mariusz who is a “community member” not affiliated with TI. So, beware that...
View ArticleForum Post: AFE5801 does internal ~10db gain (fig. 19) with external and...
When the input to the AFE5801 is AC-coupled with a 0.1muF capacitor and the analog high-pass filter is enabled a ~10db gain is observed for 50kHz input frequencies as shown in figure 19 of the spec...
View ArticleForum Post: RE: Could you provide IBIS model of ADC128S022 to me?
Can anyone answer David Liu's request ? The ADC128S022 IBIS is not available on the TI website and is required for one of our projects.
View ArticleForum Post: RE: TSC2046EIPWR touch controller is getting hang on 8KV contact...
Hi All, The above post was based on the feedback from our customer on the ESD tests, we have done some experiments and below are the inferences/corrections on above reported issue, 1. ESD failure is...
View ArticleForum Post: Simple RC LPF cut off frequency derivation-Need calrifications
Hi, Can anyone please explain the concept of cut off frequency in filter circuits? Please take simple RC LPF.How to derive its cut off frequency. When I checked in various books, they are saying like...
View ArticleForum Post: RE: TSC2046EIPWR touch controller is getting hang on 8KV contact...
Hi Siva, Below are my comments: a) Try other types of ESD diodes. b) Another thing that the customer can try is to put a series resistor in the analog lines from the driver to form a low-pass filter on...
View Article