Forum Post: RE: DRV8662EVM: Suggestions for FET switches for connecting...
Hi Kate, Sorry I have been travelling and didn't get a chance to look into this. I think the issue is that this FET can drive a huge current (80A). Therefore the FET capacitance is very large. I would...
View ArticleForum Post: RE: DRV2605L: Water repellent solution
Hello, We don't currently have information regarding a solution like this. I think the solution would use piezo technology for ultrasonic vibrations. Do you have a specific actuator in mind that can...
View ArticleForum Post: RE: DRV8601: Driving a DC Actuator directly
Hey David, I looked it up and everything suggest that it can do what you need. So I would say that this is the part you could use for your application. Best regards, Marko
View ArticleForum Post: RE: DRV8662EVM: Suggestions for FET switches for connecting...
Hello, No worries and thank you for your reply. Just to confirm, would this work for AC switching as well? From what I understand, AC switching requires two MOSFETs connected by gate and source. With a...
View ArticleForum Post: RE: TSC2013-Q1: About Interrupt signal
Hi Luis san Thank you for your support. I understood we should set D[6:3]=0000 or 0001. Sorry I have one more question, I don't know how to write the register. Please tell me the how to set it. Do you...
View ArticleForum Post: RE: TSC2013-Q1: About Interrupt signal
Hi Ogane-san, This device has a GUI and EVM in order to review its behavior, but the GUI is limited and you can't write at the registers. You can refer the Programming section of the datasheet to find...
View ArticleForum Post: RE: ultrasonic detection chip or module recommended
Hello Chen, Was the link provided helpful? Do you have any other questions, or ready to start a design? ~Leonard
View ArticleForum Post: CCS/DRV2605LEVM-CT: Once working code now doesn't work. Pls help
Part Number: DRV2605LEVM-CT Tool/software: Code Composer Studio Hello people, I'm a 3rd year electrical engineer student at Netherlands. I'm doing an internship and my assignment is to develop haptic...
View ArticleForum Post: RE: CCS/DRV2605LEVM-CT: Once working code now doesn't work. Pls help
Hello Marcin, thank you for posting your problem to E2E. I am not a programming expert and am not sure if I can help you with this, so I ll check this with my colleagues, maybe somebody already ran...
View ArticleForum Post: RE: CCS/DRV2605LEVM-CT: Once working code now doesn't work. Pls help
Hi, Marcin: what i can think of is to do some cross check. the reason may be one of the following: build environment changed? have you updated the version of CCS before it goes bad? hardware error, do...
View ArticleForum Post: RE: DRV2605L: Water repellent solution
Hi Kelly Thank you for your information. We might have to obtain detailed specification offered from customer. I would close this thread with your information once, thanks! BestRegards
View ArticleForum Post: RE: DRV2511-Q1: Could the analog input be used for current...
Hi Frank, The input influence on the PWM is described in section 7.3.2 of the datasheet and figure 4. Let us know if you have any more questions.
View ArticleForum Post: RE: CCS/DRV2605LEVM-CT: Once working code now doesn't work. Pls help
The problem was in the hardware. The debug box from TI stopped working plus I changed one thing in the dev board. After getting new debug, and putting the dev board to previous settings. The code works...
View ArticleForum Post: RE: TSC2013-Q1: About Interrupt signal
Hi Luis san Thank you for the reply! We can change register, so thank you for your support! Sorry, I have one question about the following parameter. -Parameter: Switch drivers drive current -Test...
View ArticleForum Post: RE: TSC2017 Evaluation Program Error
Hi, I tried to install the TSC2017 Evaluation Program for Windows 10 but I have an error message: The Third Partu IFN does not contain digital information signature. Could you help me please? Thanks,...
View ArticleForum Post: DRV2700EVM: DRV2700EVM
Part Number: DRV2700EVM Hi, I'm using the DRV2700EVM Evaluation board and control it with the Piezo Control Console 1.2.9. When I adjust the lowest frequency (10Hz) the signal on the output (GND; out+)...
View ArticleForum Post: RE: TSC2013-Q1: About Interrupt signal
Hi Ogane-san, Could you provide me more details? I need more information in order to get this value. Best Regards José Luis Figueroa Applications Engineer
View ArticleForum Post: RE: DRV2700EVM: DRV2700EVM
Hey Roman, welcome to E2E Forum and thank you for posting your question! If you check the DRV2700EVM User's Guide, page 25 on the schematic you will find these 2 capacitors, that are connected directly...
View ArticleForum Post: RE: TSC2013-Q1: About Interrupt signal
Hi Luis san What do you need information? I would like to konw only this paramerter meaning Best Regards, Sho
View ArticleForum Post: TSC2017: Can't access the TSC2017 from software using visa
Part Number: TSC2017 Hello I have a TSC2017 touchpad ( TSC2017EVM-PDK) , connected to my computer on USB. I am trying to access it from my software using the visa library on python. My problem is that...
View Article