Forum Post: ADS7846 EMC problems
Hello TI,Here a brief description of the EMC problem:The device, an industrial PC complied with all necessary EMC tests in the laboratory, except the DIN EN 61000-4-6 test.This test applies RF stress...
View ArticleForum Post: DRV8601 Drive Control
Hi,We are using the DRV8601 and the current design is driving it with a PWM signal. Two questions:1] Is there an applicaiton note that provides direction on PWM controls (e.g. frequency, duty cycle,...
View ArticleForum Post: Low-noise, low-drift and stable Voltage Reference
For biasing a bridge driving 100-ohm RTD which is a better 10V Voltage Reference - REF102 or REF5010? or somthing else?Which one will have longer life?
View ArticleForum Post: RE: Thermal Response of LM35 in TO-220 package.
Hi Igor,It takes longer time than I thought to get the thermal response. I will submit a request, but to speed the task faster I will setup a bench in the lab with stirred oil bath for the thermal...
View ArticleForum Post: RE: TMP006 Need a subroutine to calculate object temperature...
I've temporarily removed the current version of the fixed-point code from this thread. If you wish to receive the new version of the code, please e-mail me at ian@ti.com.Best regards,Ian Williams
View ArticleForum Post: RE: differential amp driver for AFE5801
Dear Smyth,About 1KHZ to 100M?Thanks.
View ArticleForum Post: RE: TMP006 Boost Interfacing
I figured out the problem. The pin layout for the EVM board is nowhere in the user guide for the boost pack. Looking through the user guides for the EVM module I found the pin layout. The pin layout...
View ArticleForum Post: RE: BQ76PL536EVM-3 Software installation
Try this one and let me know if you are having problem. (Please visit the site to view this file)
View ArticleForum Post: RE: AFE5808A ramp problem
Hi Haim,Your output format is probably set into 2's complement (ADC Register 0x4[3]=0). Change ADC Register 0x4[3] into logic '1'.Read more in AFE5808A datasheet in Table.2 on page 28. Regards,Mariusz
View ArticleForum Post: RE: functioning of LM 96570
Hi Chandu,For convex transducer the directional steering is not implemented in the software. It only works with linear probe.Change the Radio Button into LINEAR in "Probe selection" groupbox. The...
View ArticleForum Post: RE: BQ76PL536EVM-3 Software installation
[quote user="Roger Hwang"] Try this one and let me know if you are having problem. (Please visit the site to view this file) [/quote]This worked. Thank you very much Roger!
View ArticleForum Post: MSC (MicroSystem Controller) family - Using SPI within AI
Dear Champion,I'm facing some obstacle while trying to send SPI (Master with ESPIT and ESPIR disabled) within ISR (PAI). The auxillary interrupts in used are:1) One Millisecond2) ADC Conversion3)...
View ArticleClik here to view.
Forum Post: AFE4300 impedance measurment
Hello,I've developed a measurement circuit with the AFE4300 Chip. Unfortunately, I have a problem with the impedance measurement. When I connect a 100 ohm resistor to the AFE4300 I get a frequency...
View ArticleForum Post: thermocouple signal conditioning
Hello everyone! If you have the signal conditioning circuit that is applicable to all type-J thermocouples , then send me its link. The range of temperature for my application is 0-100 degree,the...
View ArticleForum Post: RE: TMP006 Student Project
Tanner,I'll do my best to answer your questions, however much of the information that you are requesting is up to the engineers creating the product (you and your team in this case) to decide. To...
View ArticleForum Post: RE: Thermal Response of LM35 in TO-220 package.
Hi Igor,I took sometimes in the lab collected the data. Since you are not responded to my previous posted, I did it anyway. Here is the thermal response stirred oil for LM35 TO-220. Sorry for such a...
View ArticleForum Post: RE: LM57B Part Numbering
Also, in ESP, there is a presentation, page 47 has a brief description of Obsolescence Policy:Analog Business Overview (ppt, 17,512 KB)22 Jan 2013 View Document
View ArticleForum Post: RE: AFE5808A ramp problem
Hi,Thank you, I already did that.anyway the problem was in the FPGA pipeline and we fixed that.Haim
View ArticleForum Post: RE: Thermal Response of LM35 in TO-220 package.
Thanks, very helpful.I did respond to your previous posting "yes, please do". Somehow it didn't go through.Please let me know if you received this message.
View ArticleForum Post: RE: tmp006 calculation
HiI'm doing application temperature sensor using tmp006 and microcontroller lm3s811 (TI).I'm having trouble writing code.If you do this project, can you send me your project?Thank youPhongHà Nội...
View Article