Forum Post: XTR 110
Hi,I have implemented application circuit provided in the datasheet on breadboard for 0 to 10 V input and 4-20 mA output.Supply voltage- 24V PMOS used - J176 (gate-source breakdown voltage of 30...
View ArticleForum Post: AFE5808/HSMC-ADC-bridge compatibility
Hi thereI'm looking at using the AFE5808 connected to Altera's DE3 via the HSMC-ADC-Bridge.Firstly, I'm just checking that the 5808 and the hsmc-adc-bridge are compatible?.... From what I can see the...
View ArticleForum Post: RE: Driving ERM using DRV2603 haptic driver
Senem,The maximum load current is based on the impedance of the load. The minimum load impedance for the DRV2603 is 8 ohms at 5.2V; however the measured maximum current is around 400mA.Thanks,Brian
View ArticleForum Post: Problems with I2c(TWI) with TMP006 .
I am trying to interface TMP006 with ATmega32u4 through I2c(Two wire interface), but the slave device (TMP006) is not providing the acknowledge on providing the address on the sda line. 400khz SCL...
View ArticleForum Post: RE: TMP006 and I2C
I am also facing the same problem but with a different micro controller...but i suppose the trick to this is proper setting of the SDA and SCL voltage levels provided by the temp. sensor . Check the...
View ArticleClik here to view.
Forum Post: Connection to LMP91200
Hi,i started create aquarium controller based on arduino mega 2560 R3 where one part is pH meter with LMP91200i have pH probe with BNC connector, not Triax like is in LMP91200 documentis connection...
View ArticleForum Post: TPS650250
In the TPS650250 datasheet 3,3uH is "required for output voltages >2.8V" but this is a bit confusing since w.c. ripple current is at VOUT = VIN/2, see analysis below. It is also a bit confusing that...
View ArticleForum Post: RE: Problems with I2c(TWI) with TMP006 .
Hello Dinesh,Providing a scope shot of the attempted I2C communication would be very helpful in resolving this issue.What is the VIH(min) and VIL(max) of the I2C pins on the microcontroller? Best...
View ArticleForum Post: RE: TMP006 Student Project
Hello Tanner,We appreciate the enthusiasm you have regarding the TMP006 as part of your project, but a major component of the senior project experience is doing your own research and making your own...
View ArticleForum Post: RE: TMP141
hello collin wells,is it possible to interface msp430 series of controllers with tmp141? if it is possible could you help me with the required documentation.
View ArticleForum Post: DRV2605 breakout board?
Hi there,I recently received a few samples of the DRV2605 driver and want to setup a simple Arduino circuit to drive a vibrating motor (e.g., one of Precision Microdrives haptic feedback specific...
View ArticleForum Post: RE: TMP275 I2C access question
Great. That's what I suspected.Many thanks for the speedy reply.
View ArticleForum Post: RE: question on DRV2605 PWM Input?
Nancy,Thanks for evaluating the DRV2605!Yes, the PWM input mode on the EVM is closed loop, because we assumed if you use an LRA that would want to use closed loop operation. That means we useautomatic...
View ArticleForum Post: RE: AFE5808/HSMC-ADC-bridge compatibility
(Please visit the site to view this file)(Please visit the site to view this file)Chris,the QSH is compatible with the QTH. That is correct. Also the HSMC adapter card is made to the HSMC I/O...
View ArticleForum Post: RE: question on DRV2605 PWM Input?
Hi Brian,Thank you very much for your quick response. It helps a lot!!!Best regards,Nancy
View ArticleForum Post: RE: Problems with I2c(TWI) with TMP006 .
Hello Dinesh,I'm glad to hear that you were able to resolve the acknowledge issue by replacing the device. Let us know if you need any further help!Best regards,Ian Williams
View ArticleForum Post: RE: analog basic
I understand your question, when S2 is closed you get a voltage of 3.3V f we consider charge conservation and another one if we consider energy conservation. But connecting a capacitor in parallel with...
View ArticleForum Post: need help for LM96551 power supply
Dear sir,I have to choose LM96551 as my ultrasound HV pulser, but power supply for LM96551 VNN, VPP and VSUB, I can't find any document or reference designs.Who can help me to make recommendations?...
View Article