Forum Post: RE: Temperature sensor for CC2530
Hello Ines,Thank your for your interest in temperature sensors.I'm currently researching on the finding you an ambient temp sensor that best fits your application. I will get back with you...
View ArticleForum Post: RE: How to build a board with few DRV2603 on it?
Toso,Thanks for looking at the DRV2603. Here are my recommendations:The DRV2603 requires a GPIO and PWM pin to operate. If you need to operate 10-20 DRV2603, makes sure both of these pins are...
View ArticleForum Post: RE: TMP302A pullup/pulldown values
Hello Andy,TS0, TS1 pins need to be treated as digital inputs. It looks like the 47k Ohm pull up on TS1 is treated as a logic '0' input (instead of logic high) due to which the part is tripping at...
View ArticleForum Post: RE: Temperature sensor for CC2530
Hello abhi,first of all i want to thank you for your response.In fact, i must design a wsn for an intelligent building : i need to measure the ambiant temperature, humidity and power-consumption of...
View ArticleForum Post: RE: Temperature sensor for CC2530
Hello Ines,Form your explanation I think TMP513 will be a perfect solution for your application. Its has 3 remote temperature channels with power system monitoring feature. You can find more...
View ArticleClik here to view.
Forum Post: RE: Problems with LM95172 at 190C
Thanks Aaron Heng for the reply, I am attaching the required screenshots here. We test it on our PCB board. We put the complete board into the oven and heat it to ~190C. #1 - Working at 190C#2 -...
View ArticleForum Post: RE: Communication with SM-USB-DIG
Please note i'm a software engineer and not a hardware engineer so i have never done this kind of program ...
View ArticleForum Post: RE: TMP302A pullup/pulldown values
Hello Andy, Glad we could help youn you out on this. These inputs are not connected to a weak pull down internally. I will take your suggestion and I do understand it is not always easy to find answers...
View ArticleForum Post: RE: Need clarification on DRV2605 please!
Brian,I don't see a link to download the firmware for the MSP430?ThanksRobert...
View ArticleForum Post: RE: TMP006 preferred layout details?
Hello Ian-san,Thank you for your comments, and I'll explain that to the customer. Thanks and best regards,Hiro
View ArticleForum Post: RE: TMP006 energy usage
Hi Harry,Assuming you are not doing something like gas detection and have a physical object of which you'd like to measure the temperature did you require non-contact IR type sensor or can you mount...
View ArticleClik here to view.
Forum Post: RE: TMP006 register 01h problem
Hello Luo,Also, adding on to what Ed has just explained, if you refer to the following pic from the document that he pointed out:As see in the above graph the temperature during the re-flow process is...
View ArticleForum Post: RE: LM4050 warmup defect
Hi Claude,sorry for getting back to you so late on your warm-up issue.Do you still have this question open?GreetingsChris Goeltner
View ArticleForum Post: LMP 91051
I am evaluating the LMP91051 to replace our discrete IR sensor front end cct interfacing to a Heimann HTS E21 xxx thermopile detector.Most thermopiles use the case as circuit common. in our...
View ArticleForum Post: RE: TMP006 register 01h problem
Hi Luo,Thank you for the information...everything so far with your setup seems correct. Keep in mind with the DRDY pin floating the DRDY function will not work properly, but if you are not using that...
View ArticleForum Post: Software/Disc for TX-SDK-V2/NOPB?
I just received a TX-SDK-V2/NOPB and the GUI software disc was missing. Does anyone have an ISO or can it be downloaded anywhere online?Any help/advice is greatly appreciated!
View ArticleForum Post: RE: TMP006 register 01h problem
Hi Luo,I had my team make the following tests per your request:Float both AGND and DGND - result = no communication or proper functionality - this is expectedFloat AGND with DGND tied to ground -...
View ArticleForum Post: RE: Communication with SM-USB-DIG
Hi Lisa,Here are a couple forum links that may help. One of them includes the firmware that is loaded into the TUSB3210, which is on the SM-USB-DIG. This may help you write the software you...
View ArticleForum Post: RE: TMP006 register 01h problem
Hi Mullins,Thanks for your fast test. I hope the issue is a single issue. Your recommendation is good to me. But I have other higher priority works. I will contact TI after I make the board volume...
View ArticleForum Post: TMP006 Calibration S0 Variation
Hi,I have used hot gun to mount 4 TMP006 chips on 4 new boards respectively. The hot gun is Steinel 3483. It was set to 310 degree. Solder flux was applied before soldering. The flux type is Alpha...
View Article