Quantcast
Channel: Data converters
Browsing all 37651 articles
Browse latest View live

Forum Post: TMP006 Calculated result stability

Hi,I have used hot gun to mount one TMP006 chip on a new board. The hot gun is Steinel 3483. It was set to 310 degree. Solder flux was applied before soldering. The flux type is Alpha NR-205. The flux...

View Article


Forum Post: RE: Temperature sensor for CC2530

Thank you so much Abhi.Best Regards,Inès

View Article


Forum Post: RE: ts3a225e jack selection

Hello, you are right, the  2SJ3018-001311  enters in the 'poor jack usage' picture (Fig. 24 of the TS3A225E Datasheet), the reason is that the RING1 is detected (not the TIP).Nevertheless, refering to...

View Article

Forum Post: RE: Communication with SM-USB-DIG

Hi Tom,Thank you for your answer ! I had already looked these discussions but i didn't understand everything ...Finaly i found an other solution. With Evalution kit bought, there was a software...

View Article

Forum Post: RE: Driving ERM using DRV2603 haptic driver

Dear Brian,I am also currently looking at the DRV2603 to drive my ERM motor.How do I set the duty cycle so that the motor will experience overdrive / active braking? I noticed from other posts that we...

View Article


Image may be NSFW.
Clik here to view.

Forum Post: Push-pull output stage configuration, common emitter or common...

Hello Everyone, I would like to ask you, if one of you can describe in detail reasons, why standard push-pull configuration of bipolar transistors is mostly used in common-emitter output configuration...

View Article

Forum Post: MSL (moisture sensitivity rating) for PC87427

Hello,I am looking for the MSL rating (mositure sensitivity rating) for this device, please:Winbond PC87427. Kind regards,Gavin. 

View Article

Forum Post: RE: What is 'Audio to Haptic' in DRV2605?

Dear BrianCould you advise me, Do i need micro controller / processor (for ex. MSP430G2553RHB) to drive a haptic actuator via DRV2605 by an audio signal or just DRV2605 is enough to drive a haptic...

View Article


Forum Post: RE: AFE0064 output current

Hi Iolanda,On the failure: The AFE0064 will not get damaged as long as the input voltage at the pins are within the Abs max ratings mentioned in the datasheet. Also, try to limit the current onto any...

View Article


Forum Post: RE: Push-pull output stage configuration, common emitter or...

Jiri,Each transistor is a common collector amplifier. The input is on the base and the output is on the emitter, therefore the collector is "common" to both.This common collector (emitter output) setup...

View Article

Forum Post: RE: Driving ERM using DRV2603 haptic driver

Hazrin,The DRV2603 has two pins that need to be controlled by an external microcontroller or processor. EN - the enable pin requires a GPIO control so that you can enable and disable the partPWM - the...

View Article

Forum Post: RE: What is 'Audio to Haptic' in DRV2605?

Brian, Thanks for reply. You have been helpful.Best Regards,Jituprakash

View Article

Forum Post: TMP006 calculated result stability

Hi,I have to posted the same question again because I did not receive any feedback from E2E after more than one week. I have used hot gun to mount one TMP006 chip on a new board. The hot gun is Steinel...

View Article


Forum Post: RE: TMP006 Calibration S0 Variation

Hi,My email address is sheng.2.luo@nsn.com.  I also sent one email to you. You can check it later.BRs,Luo Sheng 

View Article

Forum Post: RE: functioning of LM 96570

Hi Shiwei,No problem, I will send you the software within a few minutes. Anyway, you can use it free also for commercial purposes. I'll be glad if it could be somehow helpfull.Regards,Mariusz

View Article


Forum Post: Software/Disc for TX-SDK-V1?

Hi,     I am davinciJ.  There is no driver and software in TX-SDK-V1 EVM kit.And the TI sales said pass a link to download,but not yet recieve.Could you help me to deal with this problem?My Email...

View Article

Forum Post: About TX-SDK-V1 powersupply?

Hi,    I have a question about powersupply.There +/- 50V , +/-10V , +/-5 , +/- 3.3 , sub and with ground on the TX-SDK-V1 kit.Could you tell me what is using for by different Voltage ?? And is it turn...

View Article


Image may be NSFW.
Clik here to view.

Forum Post: RE: DRV2603 pinout

Des,Can you please request the full datasheet which contains the pin out information?  The request link can be found on the DRV2603 product webpage.  Thanks,Brian

View Article

Forum Post: RE: AFE4300 different result with AC rectification and I/Q...

Hello Juan,I have attached the document in the thread below:http://e2e.ti.com/support/applications/high_reliability/f/30/p/256837/900130.aspx#900130Let me know if you have issues accessing the document.

View Article

Forum Post: RE: AFE0064 output current

Hi Nagesh,thank you for your reply. Taking in account point 1 and 2 the linearity is ok. I am aware of the DDC264 and I am already using the evaluation board; only problem is that we do not have a...

View Article
Browsing all 37651 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>