Forum Post: LMT84 Supply Current
Hi, Below is a section extracted from page 4 of LMT84 datasheet. (http://www.ti.com/lit/ds/symlink/lmt84.pdf) On point 5, it says the input current is only 0.001uA. Is that true ? What is the “1uA...
View ArticleForum Post: RE: LM96551
Hi Grzesiek,1) When the IC is overheated, the OTP pin goes low. One can tie the OTP to the EN pin to disable the pulser. The VSUB current can be as high as 30mA (CW mode, all 8 channels on, 500pF...
View ArticleForum Post: RE: AFE4300 different result with AC rectification and I/Q...
Ok Praveen, I've downloaded the document, thank you so much!
View ArticleForum Post: RE: DRV2603 pinout
Exactly what is accomplished by NOT making the pinout of an IC widely available? I find this to be quite irksome.
View ArticleForum Post: RE: About TX-SDK-V1 powersupply?
Hi Charles, Thanks for your answer,It's really very import for me~Thanks again.Wrong power will burn the Board.May I ask more detail??The +/-50V, +/-10V, 3.3V & sub are used by the LM96551...
View ArticleForum Post: Need Help for Ultrasonic Imaging Applications of...
Hi, everyone. I recently use a set of TI product for ultrasonic imaging. Here are several problem that I have met. Really Need your help T_T !Q1: I have already read Mariusz’s post...
View ArticleForum Post: RE: AFE4300 different result with AC rectification and I/Q...
Hi again Paveen.I have a doubt regarding with the electrodes, It came from watching some comercial scales which I will use as reference for my design, I noticed that they dont use a conductive material...
View ArticleForum Post: RE: LM96551
Hi Grzesiek,When MODE is set to HI, only one set of outputs are active. When MODE is set to LO, two sets of outputs are active. You can probe the MODE pin to make sure when you set MODE to HI, it's HI...
View ArticleForum Post: RE: LMT84 Supply Current
Hi CM,I will look into this, and get back to you soon.Aaron
View ArticleForum Post: RE: Software/Disc for TX-SDK-V2/NOPB?
I just received a TX-SDK-V2/NOPB without the GUI software disc. Where can I download the GUI software and userdocumentation?Thanks,
View ArticleForum Post: TMP20 Questions
Hi,My customer has an application that requires a very low current consumption temperature switch/sensor, ideally 1uA or less,as it is powered from a coin cell battery. And it has to trigger when the...
View ArticleForum Post: RE: TMP20 Questions
Hi ZD,Thank you for your question regarding TMP20 and low power consumption. I will look into any existing data regarding duty cycle modulating the power supply and come back to you in this forum thread.
View ArticleForum Post: TSC2006EVM
We are a contract manufacturer developing a LabView test program for a product using the TSC2006. We have the EVM up and running just fine. However, the LabView app is not programmatically callable...
View ArticleForum Post: RE: Need Help for Ultrasonic Imaging Applications of...
Hi Shiwei,Q2: You can use the LM96551 to reduce the number of supply by two. It has build in LDOs for the +/-40V.Q3: When you use CW mode, you need to lower the VPP & VNN supplies to +/-5V or so....
View ArticleForum Post: RE: About TX-SDK-V1 powersupply?
Hi Fu-Sheng,The documentation is back in the web now. Sorry for the inconvenience. I attach a slide of the lab bench power supply setup for the TX_SDK_V1 that my coworker did. If you have further...
View ArticleForum Post: RE: Software/Disc for TX-SDK-V2/NOPB?
Hi All,Please download the software @ http://www.ti.com/tool/tx-sdk-v1Regards,Charles
View ArticleForum Post: RE: LMT84 Supply Current
Hi CM,Sorry for the delay. After I reviewed the datasheet, I realized that it's an erroneous note that will be deleted. Sorry for any confusion.Aaron
View ArticleForum Post: DRV201YMBR
Hello,we are using the voice coil motor (VCM),we intend to change the direction of the motor using driver, the part number of driver is "DRV201YMBR" , So please do inform is it possible to change the...
View Article