Forum Post: RE: AFE5809 VCAT response time by SPI configure including the SPI...
Hi Winston,please find below the answer.The AFE5809 can work with a max SCLK of 20MHz which means 50ns period. With that being said, as the serial data is loaded into the register every 24th SCLK...
View ArticleForum Post: RE: Power consumption by LM 35 connected to 5 Volts?
Hi,The absolute Maximum Ratings only list the maximum output current for the analog output pin and that is 10mA. They do NOT list the absolute maximum supply current. The output current will depend on...
View ArticleForum Post: peak detector design for high speed ADC line
hi, I have one problem, I am working on ADC signals and the type of square wave generally obtained has rise and fall time of 10ns roughly and stable level time of 80ns, so in total 100ns ON time....
View ArticleForum Post: RE: Need recommendation regarding LM99EVAL evaluation board
Hi Chris,Unfortunately, I have no ideality factor and series resistance information for the LM99. I was unable to find the information from the previous Apps Engineer. Most of our portfolio is all fix...
View ArticleForum Post: RE: TS5A2066 for JBUS
If you want to use the TS5A2066 on the logic level data it should work fine.You can not use it on the differential RS485 bus side because the diff pair can see very high voltages relative to the 5.5V...
View ArticleForum Post: RE: LMP91050 Differential Measurements
A have two channel thermopile HTS E21 http://www.heimannsensor.com/Datasheet-3a-Dual_Quad_rev2.pdf . Can be used "IN" and "CMOUT" pins of LMP91050 as differential input? I plan to connect the pin...
View ArticleForum Post: RE: Does LM96511EVK include a WAVEVISION5 CAPTURE BOARD ?
Dear PeymanThank you for your kind reply.I also send this information to the customer.This projedt is a brandnew ,so they are interested about it.Best regards,Shinichi Inoue
View ArticleForum Post: RE: AFE5809 VCAT response time by SPI configure including the SPI...
Hi Winston,please find below the answer.The data for this are not readily available and are not in the datasheet. If this is a critical spec, we can dig deeper and make this measurement. Please let...
View ArticleForum Post: RE: Damaged AFE5808 in Evaluation Module
Hi Chuck,I do also own an AFE5808A_EVM and I'd like to place a heatsink on the AFE as well but I don't find any standard solution, could you provide me any reference?About the holes present in the EVM,...
View ArticleForum Post: RE: Touch Screen Aircraft Seat Controllers
Hi William,Sounds like a pretty cool application. Is it for infotainment purpose?TI has pretty good resistive/capacitive touch screen controller portfolio and you can find more information here:...
View ArticleClik here to view.
Forum Post: doubt in datasheet of LM96570
Hi,I have some doubts in using the LM96570 IC. 1) In data sheet of LM96570 are mentioned as default values, so shall I assume those are the values of registers when powered up before programming...
View ArticleForum Post: TS3A4751 positive supply current
Hello, I have some questions about TS3A4751. (1)Could you please kindly let me know below conditions positive supply current ?---Conditions-----------V+:3.2VVI:2.4V and 0.4V------------------------I...
View ArticleForum Post: RE: TMP101 Alert Signal
Hi Sasikumar,Thank you for your question regarding TMP101...yes the Alert pin is open drain.
View ArticleForum Post: RE: Can the TMP006 be used as PIR motion sensor?
Hello Derek,Thanks for posting the question on the feasibility of using TMP006 for PIR motion sensing application. I will inquire with the team and get back to you with more information on this.Best...
View ArticleClik here to view.
Forum Post: RE: TMP112 I2C communication
Hello Sebastian,Pointer Address default value/reset value is 0x00 which means it is pointing to the Temp Register. You should be able to read the temperature without re-writing to the pointer register...
View ArticleForum Post: i need to help about sensor temperature,sensor detection flame...
Hello,I have a project use sensor to detect fire in room,i use sensor temperature to measurementtemperature ambient,use sensordetectionflame and sensor detectorssmokeI am surveying about sensorsCan you...
View ArticleForum Post: Touch coordinates for Saef display
(Please visit the site to view this file)Hi,1) I am using Saef display(128X160) and tsc2046 touch device.I want to know what are the minimum and maximum coordinates for my touch. Since i am using 12...
View ArticleForum Post: RE: Thermal ressponcse of LMT87-Q1
Hi Tushio,Please ask the customer if thermal response time in stirred oil would provide them the information they need?The information you supplied does say how this is measured. Also the pcb layout...
View Article