Forum Post: doubt in Tx_sdk_v1 EVM
Hi, I have one doubt in using tx_sdk_v1. To generate the high voltage +/-50v voltage pulses we are giving the +/-50v power supplies to the pulser IC. But I want to generate the <50 v (15 or 20v...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi, I have one doubt in using tx_sdk_v1. To generate the high voltage +/-50v voltage pulses we are giving the +/-50v power supplies to the pulser IC. But I want to generate the <50 v (15 or 20v...
View ArticleForum Post: RE: TS12A12511 SPDT Switch functionality w/o power applied
Eric,I agree. Can you move the post for us?Mark
View ArticleForum Post: RE: LMP91200 issues
Hi, I know this sort of thing takes time, is there anyone at TI that can comment on this?
View ArticleClik here to view.
Forum Post: RE: Questions about TX-SDK-V2 EVB
Hi sir,thank for your reply, it is very useful for me. I have some more doubts, please guide me sir.1) For transducer connection at SMA connectors in Tx_sdk_v1, manual mentioned that need to remove...
View ArticleForum Post: RE: need guidence in powering of Tx_Sdk_V1 EVM
Hi,Please some body who knows about Tx_sdk_v1 powering answer to my questions. It is usefull and urgent for me. thank you.regards,chandu.
View ArticleForum Post: RE: Questions regarding your schematic of Thermistor Transducer...
Sorry, I forgot the schematic.
View ArticleForum Post: RE: TS12A12511 SPDT Switch functionality w/o power applied
Has anyone been able to look at this post?Thanks for your help with this!Richard Elmquist
View ArticleForum Post: RE: DRV8662_Maximum voltage_varying for frequencies
Karun,Unfortunately the amplifier GBW cannot be widen in the current design. If the voltage limitation is because of the boost loading, you may try increasing the current limit resistor assuming a new...
View ArticleForum Post: RE: doubt in Tx_sdk_v1 EVM
Hi Chandu,Please see my earlier reply. Basically, just apply +15V to VPP and -15V to VNN if you wan to generate +/-15V at the output.Regards,Charles
View ArticleForum Post: RE: need guidence in powering of Tx_Sdk_V1 EVM
Hi Chandu,Yes, you can communicated the Opal Kelly board with the TX_SDK board.Regards,Charles
View ArticleForum Post: RE: About TX-SDK-V1 powersupply?
Hi Spiros,To get positive supply voltage from the power supply, the -ve connection is connected to ground and the +ve connection is connected to the desire positive voltage. To get negative voltage...
View ArticleForum Post: RE: TS12A12511 SPDT Switch functionality w/o power applied
Hello All,The short answer is trying to "Power" the part through the ESD structure is operating outside datasheet specs and neither device operation nor longevity will be guaranteed. Regards,Andrew
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi sir,Thank you for being informative.I am facing error in GUI getting connected to the hardware set up. And the power supplies are vpp(50v)=15v, vnn(-50v)=-15v, vdd=10v, vdn=-10v ,vsub=-20v, 3.3v,...
View ArticleForum Post: RE: LMP91200 issues
Hi Timothy,I assume that you have configured the LMP91200 in pH mode and you have configured VOCM in order to have the VCM voltage at the VOCM pin.Where do you connect the DMM in your board and in the...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi,thank you for your reply.I think no problem with opal kelly board driver installation because, It was showing that connected in device manager.And opallkelly board drivers are supported for...
View ArticleForum Post: RE: About the package(BGA ball) size of TMP006.
Dear Muppiri-sanThank you for the quick reply.regards,Satoshi
View ArticleForum Post: RE: About the package(BGA ball) size of TMP006.
Hello Satoshi-San,Glad to be able to help. Is this information intended for Soldering the WCSP TMP006 on to the PCB? Regards,Abhi
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi Chandu,When I mention the software was written for Windows XP, I mean the TI GUI software not the Opal Kelly. If you can find a Windows XP machine, it might be good to try it.As for training, I...
View ArticleForum Post: RE: TS12A12511 SPDT Switch functionality w/o power applied
Andrew,Thanks for your response.Richard Elmquist
View Article