Forum Post: AFE5801 stability issue?
Hi, I am using AFE5801 for my imaging board and have been experiencing some strange behavior.I have MAXIM14811 pulser, MAXIM4937 TRSW.When I send out a pulse, AFE first gets saturated and goes into a...
View ArticleForum Post: RE: Cap. touch: sense touch on both sides of PCB?
Fredrik,Interesting idea....I think this could be done fairly easily with a 4-layer board. A couple of things to watch out for.Make sure there are no vias that go from a CapTouch button on one side to...
View ArticleForum Post: WCSP Ball Grid Array Mount
I have a 9 pin WCSP Ball Grid Array IC that I'd like to mount onto a PCB. I need to build a prototype using the DRV2605 and I don't have ant PCB etching equipment. Are sockets or mounts available for...
View ArticleForum Post: RE: LM35 UB Certification
Hi Aaron,I am sorry that it took long time to get feedback from my customer.Thank you for sending me the report. I provided it to the customer,and their end customer was ok with the report.Thank you...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi sir,thanks for your reply .sorry sir, you are absolutely right sir. Now with the Win xp I could get the GUI working.Now to get start up,Individual Device Evaluation to test LM96570 and LM96551. I...
View ArticleForum Post: RE: DRV2603 pinout
Dear Des,The pinout in the datasheet is different from what you wrote, it is actually:10 GND1 EN 9 OUT+2 PWM 8 GND3 LRA/Not ERM 7 VDD4 NC 6...
View ArticleForum Post: RE: AFE5808A LSB and Amplifier
Jin, I have found what I believe is your issue: you are not actually feeding 10mVpp to the AFE input. Is there a way that you can confirm this? The AFE 50ohm activate termination does not work with...
View ArticleClik here to view.
Forum Post: RE: DRV2603 pinout
Pierre,Thanks for correcting this. Here is the pin-out from the datasheet. The datasheet can be requested on TI.com through the DRV2603 product webpage.Thanks,Brian
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
hello sir,sorry for asking again, But I did not violate the absolute ratings of Beamformer, pulser and switch as per data sheets.When I was first gave the power supplies to the board, That time in...
View ArticleClik here to view.
Forum Post: RE: Questions about TX-SDK-V2 EVB
Hi Chandu,I am sorry for your trouble. But did you power up the 1.8V supply before powering the 3.3V supply? (As you posted on Aug 12). You should power up the 3.3V then the 1.8V...
View ArticleForum Post: Analog Applications Journal
Hi,Reading last editions of TI Analog Applications Journal, I have found there a lot of useful ideas and information about DC-DC converters (and not only them) which usually are not considered in the...
View ArticleForum Post: Measuring Temperature of an aluminum plate
I am trying to measure the temperature of an aluminum plate. I want to mount the surface mount package upside down to keep the pins from the plate. Will this mounting style give an accurate reading?...
View ArticleForum Post: RE: Temperature controlling of a pan
Hi Gurkan and Mike,Let me look into this, and get back to you soon.Aaron
View ArticleForum Post: RE: LM95231 CIMM address issues
Hi Omer,That was very strange. I will try on my bench sometimes tomorrow. Could you please provide me the snapshot of SMBDAT and SMBCLK when the software communicates to CIMM (address 0x57)? Did you...
View ArticleForum Post: capacitors in single polarity split rail supplies
Hello all,A novice question. I want to use a TLE2426 rail splitter in conjunction with a BUF634 op amp buffer to create a split power supply (half my battery supply voltage) for use in...
View ArticleForum Post: RE: Temperature controlling of a pan
Hi Gurkan and Mike,The LM35 has a typical accuracy ±0.25°C at room temperature and ±0.75°C from -55°C to 150°C. Most of our temperature sensor products are sensed the temperature through the sensor’s...
View ArticleForum Post: RE: LM95231 CIMM address issues
Hi Omer,I'm sorry for the confusion. I meant the LM95231BIMM. I checked my old software and the evaluation software. We had the address 0x2B for LM95231CIMM. The datasheet has a typo. Sorry for any...
View ArticleForum Post: RE: Measuring Temperature of an aluminum plate
Mike,Thanks for posting your question on E2E. I believe Ed has already addressed this via email. Do let us know if have any further questions or concerns.Regards,Abhi
View ArticleForum Post: RE: Lots about AFE's but what about row gate drivers ?
Hello Randall,and thank you for your message.At the moment TI does not offer a gate driver IC for X-ray Flat Panel Detector (FPD).Timing and voltage levels might be specific to the FPD that you would...
View ArticleForum Post: RE: LM95231 CIMM address issues
OK, thanks for the prompt response , im sure it will do the job I had the feeling it is something like that :)
View Article