Forum Post: RE: LM35 load current
Hi Whynn,I will look into this, and get back to you tomorrow.Aaron
View ArticleForum Post: LMP7721 in a potensiostatic application AN-1798
Hello, I wonder if the LMP7721 in the proposed circuit in AN-1798 can read currents in the range 0-300 nA.Thank you.Best regards,Alejadro
View ArticleClik here to view.
Forum Post: RE: Questions about TX-SDK-V2 EVB
Hi Friday,1) We use BAS40 as the Schottky diodes2) When you transmit, you should closed s1. When you receive, you should open s1. Also make sure your bridge diodes can handle the transmit voltage...
View ArticleForum Post: RE: AFE5808
Hi, Thank for your information on VCAT. Similarly I just want to know the purpose, working of the blocks of AFE5808(LNA,VCAT,PGA,LPF) , Can provide document or its source, which can specify about the...
View ArticleClik here to view.
Forum Post: RE: Questions about TX-SDK-V2 EVB
Hi Friday,Sorry you can't see the schematic. Let's try again. The schematic is not on the LM96511 datasheet. It's part of our internal demo board. As you can see from the schematic, the external diode...
View ArticleForum Post: RE: LM35 load current
Hi Whynn,I’m sorry for delay. The LM35 can only source current up to 1mA. Based on your configuration, the amount of current sink into the part is about 40uA, where the device can sink about 4uA. There...
View ArticleForum Post: Analog isolation
Hi Friends; I want measure a DC line about 120V ; but I want to isolate the DC line from my ADC ; do you suggest a cheap solution ? ISO124 is expensive one . Thank you
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi Charles, any news for the power supply release ?Best regards.
View ArticleForum Post: RE: photo-diodes and spectral sensitivuty
Hi,I think I can proceed like comparing the output current with/without the sample.
View ArticleForum Post: RE: photo-diodes and spectral sensitivuty
Hi,Another option and super simple and easy to breadboard with is OPT101...it has the photodiode already itegrated into the device along with single supply transimpedance amplifier and 1Meg Ohm...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi Olivier,We are hoping we can release the power module schematic to web later this week.Regards,Charles
View ArticleForum Post: RE: About Temperature Data Format of TMP006.
Hi Satoshi,Thank you for bringing this error in our data sheet to our attention...you are correct. we have made the necessary changes and are in the process of rereleasingvthe corrected data sheet to...
View ArticleForum Post: RE: TMP100-EP (i2c interface) STOP condition
Hi Ashok,Thanks for your question...for continuous read operation you will not require a stop at the end of each I2C sequence. once you have established the pointer regsister you can issue a chip...
View ArticleForum Post: TSC3060EVM availability and purchase
Hi,I'm interested in purchasing a TSC3060EVM. The eStore doesn't have these evaluation boards listed. Is there a special process for this?Thanks, Kirem
View ArticleClik here to view.
Forum Post: RE: Ultrasound transducer interface to pulser outputs
Hi, Actually I have designed individually customized boards for the pulser(lm96550), Beamformer (lm96570), tx/rx switch (tx810) with reference of Tx_sdk_v1. The below Image shows the beamformer...
View ArticleForum Post: RE: AFE5808
For medical diagnosis to get Time gain compensation, Can you suggest me VCNTL analog signal. I think it is ramp, but I can't understand what should be the frequency. On what criteria the analog signal...
View ArticleForum Post: AFE5809 Speed Grade
Hi,Could someone please provide for me the speed grade of the AFE5809?I need this to set up the ALTPLL on my Cyclone V.Also are there any examples on LVDS with the AFE5809?Thanks!Jack
View ArticleForum Post: RE: About Temperature Data Format of TMP006.
Dear Edward Mullins-sanThank you for the early reply.Carrying out introduction Update next year, I understood.A point in question becomes clear and appreciates.Best regards,Satoshi
View ArticleForum Post: Spike LMX2364
We have problems with the LMX2364 . PLL in the circuits creates a variable frequency between 9 and 10GHz and we have discovered that the lost nail in PLLens output ( that controls a discrete VCO) ....
View ArticleForum Post: RE: Ultrasound transducer interface to pulser outputs
Hi Chandu,Does the pulser output get less distorted when you set B3B2B1 to 000 or 001? I am not familiar with the TX810. However, looking at fig 14 of the TX810 datasheet, it might loading the output...
View Article