Forum Post: Preset temperature for LM26LV temperature switch
Datasheet for LM26LV says TRIP temp can be preset to any value from -50C to 150C by varying the gain but orderable parts only come at 50C to 150C for every 5 degrees apart. How I can have a part with a...
View ArticleForum Post: RE: TMP101 ALERT Output
Hi Abhishek,Qestion to answer.1. 0.1uF Ceramic Condencer x1 Piece (between 3.3V to GND) 2. Anyway, since it is a talk immediately after power activation, even if it is a register, it has not set up....
View ArticleForum Post: uaf42 low pass butterworth design problem
Hello,I am trying to implement the 2nd order butterworth LP filter for cutoff frequency 70Hz using UAF42 IC and I selected the components as per FILTER42.exe DOS version software and I used subcircuit...
View ArticleForum Post: RE: The question about LM98620
Hello,Mr.HoomanThank you for quick reply.I undestood TX0 to 6 content by Table 13 however I can't understand GPI[5:1].Let me ask you three question.1)What does Ch1.(1) ,Ch(2) mean ?2)What is the data...
View ArticleForum Post: Error on App. note http://www.ti.com/lit/an/slua622
Applications Note "Digital Loop Exemplified" at http://www.ti.com/lit/an/slua622 contains a significant technical error on page #5.Specifically the equation for Fp3 is incorrect. This pole exists at...
View ArticleForum Post: RE: TLV431B
Use a Type II compensator. The following app notes provide all the info you...
View ArticleForum Post: RE: LM95701 accuracy error
Hi Liron,The accuracy of the LM95071 cannot be tightened. Please keep in mind that the accuracy is only guaranteed with a supply voltage of 3.3V to 3.6V please see the EC table on page 5 each accuracy...
View ArticleForum Post: RE: Linux Kernel 3.0 Driver for LM92
Hi Olaf,You should be able to find a Linux Kernal driver at: http://www.lm-sensors.org/wiki. It might be for an older version of LInux but you are be able to request a new one there if it doesn't work...
View ArticleForum Post: RE: Temperature Sensor IC → LM20 vs. LMT89
Hi Eric,The LMT89 is an alternative to the LM20 whose accuracy is not as tightly guaranteed. Please compare the accuracy specifications in EC tables on page 4 of the datasheets for more details.Also...
View ArticleClik here to view.
Forum Post: RE: The question about LM98620
Hello Mr.HoomanThank you for quick reply.I understood that you wrote.Ｉ post pin arrangement of a Cmos sonseor that customer made to following.They seem to use 6 CMOS sensors for one LM98620.If you...
View ArticleForum Post: RE: About power-supply of LM965xx chipset
Hi Konstantin,Regarding item #4, I am able to a hold of the EVM, CB9A and CB10A are on the bottom layer. However, I can't find CB6X or CB4X on the board. I still recommend you put 10uF cap between VPP...
View ArticleForum Post: RE: TMP101 ALERT Output
Hello Hisakichi-san,Thanks for the answers. Can you advise the customer to turn off TMP101 for a longer duration say for about 1 second and see it if this issue occurs again.To be able to advise you...
View ArticleForum Post: RE: Using TPM102 to sense ambient temp
Hello AQ,Using a thermal conductive goop for measurng outside plastic enclosure temperature changes may not be the right approach, especially if you are trying to achieve a quick response. In fact...
View ArticleForum Post: Simulation of Analog Multiplexer!
I am using the Texas Instrument's SN74LV4051AN (Analog Multiplexer) in my design. I wish to Simulate it before applying it on hardware. Is there any way out how to simulate this...
View ArticleForum Post: RE: LM95701 accuracy error
Hi,I undestand datasheets are written also in a marketting manner rather than technical mannerstill I cannot understand how two sensor prohibits a different of 3.5 degrees from each other although the...
View ArticleForum Post: RE: TSC2004 AD0,AD1pin processing
Hi members.This problem, I solved.The EVM's specification was written A0, A1.Thank you .BEN.
View ArticleForum Post: c# interface with TMP006EVM
Hi there,I am writing an application to interface with the TMP006EMV. In some threads I have seen that the communication is established through HID USB.My application is written in C#.Does anybody know...
View ArticleForum Post: RE: Piezo Vibration sensor
Milan, I am not sure which Piezo sensor will give you the best results, but i did find some links that may help you once you find your energy harvesting...
View ArticleForum Post: RE: About power-supply of LM965xx chipset
Hi Konstantin,5) The reason you want to minimize the ESR is because during transient, the peak current on both VPF and VNF could be 1A (all 8 channels on). 6) We don't have any official recommendation...
View ArticleForum Post: RE: functioning of LM 96570
Hello Mariusz,thanks .it would be highly appreciated, if you could share some information/ reference papers or documents on how to calculate the delay values for beamsteering a curvilinear array...
View Article