Forum Post: counter
HiCan anyone suggest a counter that can divide the frequency upto 100MHz
View ArticleForum Post: RE: Driver of Windows Touch
Hi Alpha,The Linux driver for TSC2046 is available right now. However, the Windows 7 driver for TSC2046 is not present yet. Is your customer capable of porting the Linux driver to the Windows 7...
View ArticleForum Post: Temperature Sensor IC → LM20 vs. LMT89
What is the difference between the parts LM20 and LMT89?Is the LMT89 a replacement for LM20?
View ArticleForum Post: RE: Inquiry regarding Power-Up/Reset Format on TMP102
Abhishek-san,Thank you for your reply on additional inquiries.Our customer could find these root cause by themselves, that the I2C device address of 2 ADCs which are mounted on this system board are...
View ArticleClik here to view.
Forum Post: RE: The question about LM98620
Hello Mr. Taichi,My response below:Q: That is, this device can accept LVDS with no CLK?A: No, the LVDS output data uses TXCLK as clock, as shown below.Q: What is ”12 Pin to 16 Pin (Selectable) LVDS...
View ArticleForum Post: RE: Inquiry regarding Power-Up/Reset Format on TMP102
Hello Atsushi-san,Glad that the issue was resolved. I understand that there was I2C bus contention. I just want to make sure i understand this correctly... is the address of TMP102 and one ADC was...
View ArticleForum Post: RE: How can I make a skin temprature monitor for children？
Hello Lance,If I haven't mistaken, you must be part of the the University of Arizona student project working on skin temperature measurement. From our interaction earlier this week it looks like you...
View ArticleForum Post: RE: wrong data from TSC2046 Touch point
Hi AndyWhen I keep pressing certain position on touch screen, the coordinate is directing another position sporadically.I'm not evaluating the evm.What I want to do is that to find differences from the...
View ArticleForum Post: LMP91200 configure as pH measumement
Hi, I´m interest for use the CI LMP91200 for measurement of pH and temperature. But i have a problem in the connection for SPI with launchpad stellaris.How configure the adress direction to file main?,...
View ArticleForum Post: RE: need help in understanding TI article AN-1852
Hi Sami,Since this team does not support this device, I am going to move your question to the Temperature Sensor forum so that it will get the right visibility and support.From a quick look at the...
View ArticleClik here to view.
Forum Post: RE: The question about LM98620
Hello Mr. Taichi,I think you are asking how the data for the different inputs (OSR1,2; OSG1,2; OSB1,2 and GPI:5) gets mapped into the output data buses serialized data.That is described in the...
View ArticleForum Post: RE: TMP101 ALERT Output
Hi all,Mistake!Power supply ON (3.3V)---> power supply OFF (about 70 msec)---> power supply ON (3.3V)--=> After about 20 msec(s) From an ALERT output For [ Low Level ] about 40 ms is outputted
View ArticleForum Post: RE: Inquiry regarding Power-Up/Reset Format on TMP102
Abhishek-san,Sorry for late response on your question.Customer said that they used TMP102 and ADS1013 on same I2C bus line as parallel.Since A0 pin on TMP102 and ADDR pin on ADS1013 were both connected...
View ArticleForum Post: RE: TLV431B
Hello Ron,thank you for the fast answer.1.) Removing C1 is not possible for my application.2.) It seems, that oscillation is getting better by adding a C in parallel to C1. But how can I justify that...
View ArticleForum Post: RE: need help in understanding TI article AN-1852
Hi Sami,As John mentioned, the LM35 is analog output voltage proportional to temperature; therefore, you need a ADC to measure the output voltage then convert to temperature using the equation in the...
View ArticleForum Post: RE: TLV431B
Nico,Increase C1 will decrease the output pole frequency (output impedance and C1). By 'better' do you mean lower amplitude oscillation or no oscillation? The formula for the 33k shunt cap, is based on...
View ArticleForum Post: AFE5808A power consumption as a function of input amplitude?
Hi,I've developed a test circuit for AFE5808A before accomplishing final application to do some measurements and tests.Lately I've discovered something that makes me confused. One time I observed, that...
View ArticleForum Post: RE: TMP101 ALERT Output
Hello Hisakichi-san,Please check on the following possible causes of the issue here:1. Do you have a bypass capacitor at the power suppy? The reason I ask is 70msec may not be enough time and TMP101...
View ArticleForum Post: RE: functioning of LM 96570
Hello Prasad,I understand you use the software I have developed. If yes, then all you need is to click the relevant RadioButton on "Probe selection" Group Box. There are two possible selections: Linear...
View ArticleForum Post: TSC2004 AD0,AD1pin processing
Hi members My customer is looking at the next model TSC2004.I can not find the datasheet and EVM'sPlease teach me this question. ① AD0 and AD1 Is it may be a open processing? ② AD0 and AD1 is...
View Article