Quantcast
Channel: Data converters
Browsing all 37774 articles
Browse latest View live

Forum Post: RE: Using LM35

Hi, i think i found the reasen. GND and VS is changed in the datasheet. Here the datasheet: http://www.ti.com/lit/ds/symlink/lm35.pdfThnaks

View Article


Forum Post: RE: AFE5801 VGA

Thanks for the reply, Chuck.  I am in the ultrasonic rail flaw detection business, where each channel needs independent variable gain with an 80 DB dynamic range.Joe

View Article


Forum Post: TMP112 interface with PIC16F690

Hello.Does anyone know how can I interface the temperature sensor TMP112 with Microchip PIC16F690?It would be a great help if someone could show an example code in C.

View Article

Forum Post: DRV5053 app notes

HI,I need to measure the supply line current. For that is it possible to use DRV5053. If yes, please help to share the some kind app notes to understand the implementation.

View Article

Forum Post: TMP103 Conversion timing

Hello,i am using four TMP103 sensors on the bus in continious conversion mode. Due to energy terms i would like to spread the starting times of the different sensors over one cycle. The only sure start...

View Article


Forum Post: RE: TSC2004EVM-PDK / Don't operate on Win7 OS

Hi Herbert-san,Thank you for your response.Now our customer can not communicate with EVM via Win7 OS PC though the Win7 driver is installed. The "USB ACTIVE" LED is not active as photo in my previous...

View Article

Forum Post: Thermal probe for TMP435

Hi,I am designing a thermal measurement application based on TMP435 device.I am looking right now for a "cable based" probe to connect on DXN/DXP device pins.This probe should looks like a:    # 2-wire...

View Article

Forum Post: RE: Closed loop Temperature Control

Hello Rahul,Most of the regular IC temperature sensors can go up to 150C. But check out our high temperature product portfolio...

View Article


Forum Post: RE: TMP112 interface with PIC16F690

Hello Natailia,I can help you with this as long as you are able to program your PIC16F690. If you already have your I2C lines connected to TMP112, its just a matter of reading register 0 of TMP112....

View Article


Forum Post: TSC2004 X and Y connection

Hello,My touch screen's outputs are named XLEFT, XRIGHT, YTOP and YBOT. How do I connect them to the TSC2004?Does it matter if I have X signals swapped (XLEFT to X+, XRIGHT to X- vs. XLEFT to X-,...

View Article

Forum Post: RE: TMP103 Conversion timing

Hello Matthias,Thank you for asking very interesting questions. When you change the CR0,CR1 bits the change takes effect immediately after the ongoing (current) conversion is completed.Since saving...

View Article

Forum Post: RE: Thermal probe for TMP435

Hello Andre,I don't think there is a ready-made cable with embedded diode/transistor option that you can find in the market. I think you will probably need to custom build it yourself. But, in general...

View Article

Forum Post: LM96194 for monitoring 12V supply.

Hi,The LM96194 device has a nominal supply voltage of 3.3V. Can this device be used for monitoring 12V supply if the 12V supply is present on the board before the 3.3V supply is generated?Regards,Prachi

View Article


Forum Post: Purpose of SPIO-4

Hi all,I am using LMP91200 evaluation board and SPIO-4. I have doubt, what is the purpose of the SPIO-4 evaluation board for communicating between LMP91200 and pc purpose or anything else. In the...

View Article

Forum Post: RE: TMP112 interface with PIC16F690

I'm having troubles with the I2C lines. So far I got this:#define SDA RC0#define SCL RC1#define SDA_DIR TRISC0#define SCL_DIR TRISC1#define SDA_HIGH() SDA_DIR=1#define SDA_LOW() SDA_DIR=0#define...

View Article


Forum Post: TMP411 / THERM2

Hi Team, I'd like to ask about THERM2 function(AL/TH bit=1).In datasheet P.12, There is the following description.----------------------------------------------------------If AL/TH = 1, the...

View Article

Forum Post: AFE5801- how to write to register, SPI based?

Hello:I searched the forums for a LabVIEW example. Specifically, I am looking for an example that shows how to write to or read the register of TI AFE5801 ADC.I am using pg. 2 & pg. 20 of the...

View Article


Forum Post: RE: LM96194 for monitoring 12V supply.

Hi, Could you please update me on the above query?Regards,Prachi

View Article

Forum Post: RE: LM96194 unused pins

Hi Aaron,I have one more doubt in this. You said that if not used, the VRD1_HOT pin must be connected to ground. But in this case, as this is an active low input, will it not be enabled by default? I...

View Article

Forum Post: RE: TMP411 / THERM2

Hello Abhishek-san, Thank you for your clear explanation.I understood. Best regards,Yaita

View Article
Browsing all 37774 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>