Forum Post: TMP006 Calibration Problem
Hello,We are having a project with TMP006 and having some difficulties in calibrating the sensors. We have some questions:1) Calibration calculationAs a recap, the followings are formulas from...
View ArticleForum Post: RE: TMP513 shunt voltage measurement offset voltage
HiI could not get good technical support from india TI technical support team, kindly improve the TI support in india.
View ArticleForum Post: RE: TMP112 / distribution graph of temperature error
Hi Mayrim-san, Thank you for your cooperation.I will wait for you and Fujiwara-san's reply. Best Regards,Yaita
View ArticleForum Post: RE: AFE5809EVM GUI User's Guide
Hi,There is a User's Guide for the AFE5809EVM and GUI on the TI website. You can download from the following link:http://www.ti.com/lit/ug/slou338a/slou338a.pdfLet us know if you still have...
View ArticleForum Post: RE: TX-SDK-V2 characteristics
Hi Yorick,The LM96570 generate pulses (frequencies) to the LM96550. With the transducer load of 150pF or greater, the LM96550 can response fast enough for frequency greater than 15MHz.Regards,Charles
View ArticleForum Post: RE: LM96163
Hi eli,I will look into this and get back to you soon.-Michael Wong
View ArticleForum Post: RE: TMP513 shunt voltage measurement offset voltage
Hi JasonThanks for your reply1. R33 used for current limiting purpose, Voltage drop in the resistor R33 is minimum.2. C112 decoupling provided,3. current measured in the input side.i will do the...
View ArticleForum Post: RE: AFE5809 maximum operating currents
Anton,We have received your inquiry about the AFE5809 and we hope to have an answer back to you shortly.
View ArticleForum Post: RE: TMP006 accuracy at close distance
Hi Ryuji,You will expect the similar +/-3 degrees Celcius.
View ArticleForum Post: RE: TMP006 Calibration Problem
Hi Kelvin,!) In response to your questions, the equations descibd in the TMP006 and TMP007 for calibration are designed to account for an imperfect world. Heat sources other than IR energy from the...
View ArticleClik here to view.
Forum Post: Problem with tsc2046 + DM365
Hardware: the DM365 + tsc2046EI + 4.3 -inch LCD and touch screen (with circuit ) Software: DVSDK (dvsdk_dm365_4_02_00_06) ads7846. C Problem: When i test the SPI2 with SPIDEV_TEST，it is...
View ArticleForum Post: RE: About MIXH pins voltage of OPT8140
Hirata-san, I will reply to you directly over e-mail as we suppose this product directly to customers.
View ArticleForum Post: RE: TMP006 accuracy at close distance
Hi Ryuji,Please have a look at TMP112...it is specifed at +/-0.5C over the range 0C to 65C. For applications that use a smaller temperature range there is information in the data sheet that allows a...
View ArticleForum Post: RE: Body temperature sensor
Hello Mohammad,Thanks for looking into E2E for product recommendations. TMP112 is perfectly suited for body temperature measurement within 0.5degC. Its one of the most widely used parts in the...
View ArticleForum Post: RE: LM96163
Hi eli,The central pad can be connected to ground. -Michael Wong
View ArticleForum Post: RE: AFE5809 maximum operating currents
Anton,I tried to post the bottom of pg. 11 of the AFE5809 DS. Didn't work though.
View ArticleForum Post: RE: Spectral range TMP006, a non-contact infrared (IR) sensor
Hi, I'm also interested in the TMP006 spectral responseI'm working on environmental sensors to monitor atmospheric emitted radiance, so I'm particularly interested in the response of the TMP006 in the...
View ArticleForum Post: TMP006 quiescent current
When I turn on TMP006 I have 260 uA. And when I turn it OFF I have 30 uA and it is sloowwly dropping too 10-15 uA. Not very stable too. All input are defined well 3.3V or 0V and have required pull up....
View ArticleForum Post: RE: TMP006 question
Hi AbhiI have a query on TMP006 sensor, which we are using in our design.In the design, TMP006 is connected to CC2541 through I2C. similarly some other sensors are also connected to same I2C bus.We are...
View ArticleForum Post: RE: TMP006 quiescent current
Hi Mayrim and Werner, I use a breakout board from Sparkfun. Datasheet is attached. I measured current in the Vcc line. I2C bus speed is 267kHz. After power up I send one command to the TMP006: to power...
View Article