Forum Post: RE: REF5050
Alexander,All of our products, including REF5050, undergo a life-time test in a high temperature oven to determine an equivalent shift of various parameters after 10-years (87,600 hours) of constant...
View ArticleForum Post: RE: TMP006 quiescent current
Schematically they are the same. However I just noticed that PCB layout of the Sparkfun breakout board (SEN-11859 TMP006 Breakout) is bad. The pull up on DRDY# is not connected. So DRDY is floating....
View ArticleForum Post: RE: LM96194 for monitoring 12V supply.
Hi Aaron,I have a similar doubt as the earlier one. I am using the AD_IN7 input to sense 5V supply. I am using external dividers so that the value at that pin is 0.984V. However, the 5V is generated...
View ArticleForum Post: RE: TMP006 quiescent current
Hi Jasper,Please let us know your results with the new TMP006 when you have them!Best Regards,Mayrim
View ArticleForum Post: RE: LM96194 reset signal
Hi Prachi,Let me look into this and get back to you.-Michael Wong
View ArticleForum Post: About flick with TSC2046E
Hi,Have you ever won the design for apps that have flick input with TSC2046E?If so, 1) was TSC2046E connected with MSP430 through SPI interface?2) could you provide us with the software/driver? for...
View ArticleForum Post: RE: LM96194 reset signal
Hi Prachi,Yes, the reset signal will be held low for 250-330ms after it hits a certain threshold voltage during power up. The part will perform a reset at 2V even though the mininum threshold voltage...
View ArticleForum Post: RE: AFE5809 Custom board based on EVM
Hi,We received your inquires regarding the AFE5809 and hope to get back to you very soon with answers.Thanks.
View ArticleForum Post: RE: LM96194 for monitoring 12V supply.
Hi,Could you reply to me regarding my query?Regards,Prachi
View ArticleForum Post: RE: Can anyone identify this TI component?
I've got more info, the part number on the schematic is AP2182SG-13-GP which is not a TI part number.
View ArticleForum Post: RE: TMP006 question
Hello AbhiThanks for the reply. We are in prototype design. As mentioned in before mail, we are designing a Fitness tracking device, where many other sensors are connected to I2C of CC2541. The...
View ArticleForum Post: Issue facing on CC430F5133 interface with SHT15 (temperature...
Im post my code , while setting UCTR for transmitter mode, and setting UCTXSTT to generate a START condition. , in the I2C comm using 10Kohm pull resistor, i cant able figure out the problem , can any...
View ArticleForum Post: RE: LM96194 for monitoring 12V supply.
Hi Prachi,I'm sorry for the long delay. I was a bit busy getting stuffs done. It should no problem when you apply 5V before powering the chip as long as you do not exceed 6V. There are two resistors...
View ArticleForum Post: RE: Display TMP112 data temperature
If temper2 is holding the Low byte of temperature data , yes this method should work. Best regards,Abhi
View ArticleForum Post: RE: TMP006 question
Hello Eshak,"we are checking the temperature with close contact touching the sensor"I hope you are not physically touching the sensor because this will affect the local temp sensor built into TMP006 to...
View ArticleForum Post: RE: TMP006 quiescent current
I received the Adafruit TMP006 breakout board, that draws exactly 240 uA and 0.4uA in standby. I guess either the Sparkfun board of the TMP006 on that board was damaged. I did not try to solder a new...
View ArticleForum Post: Process/wafer size
Hi,where i can find the wafer/process size for comparators? can any one help me?RegardsSindhu.V
View ArticleForum Post: RE: AFE5809EVM design files
Hi Chuck,Can you make a gerber file off the différents layer?Or if you can generate an Altium/ Eagle project it would be very niceThanks for allSam
View ArticleForum Post: RE: LM95233 / about TCRIT function
Hi Kato-san,I will get back to you soon.Aaron
View ArticleForum Post: ADS7846 ADC VALUES NOT CORRECT
Hi e2e,We have a customer starting a new design based on the ADS7846. They have the following questions:What is the 12 bit output data format from the AD7846? To get the 12 bits the AD7846 must be...
View Article