Forum Post: RE: Help: Two current transmitter XTR115 in the same board
Hello,how i can isolate the inputs from each other? I know the principle construction of the system. So my question is, are there any ICs which transmits a 0V-5V analog signal to an isolated 0V-5V...
View ArticleForum Post: RE: How to do soft reset or clear ALERT interrupt in tmp102...
Hello Shabbir,Thanks again for the detailed explanation of your requirements. I have a suggestion other than your General call/software reset option. Put the device in Comparator mode (POL=0) then Set...
View ArticleForum Post: RE: Help: Two current transmitter XTR115 in the same board
look thishttp://www.ti.com/product/dac8760RegardsGastón
View ArticleForum Post: LM98714 Initialization code
Hi Members.I am new to LM98714so pls help me to initialise LM98714,Am trying to initialise the device in CMOS mode and with out CCD timing generator, my INCLK is 50Khz.RegardsGovind Raj
View ArticleForum Post: RE: How to do soft reset or clear ALERT interrupt in tmp102...
Hi Abhi,This seems a good solution. I'll try and let you know if i still face any problem. Thanks abhiShabbir Limdiwala
View ArticleForum Post: RE: LM95233 / about TCRIT function
Hi Kato-san,TCRIT pin will trigger to a LOW when the temperature reaches to TCRIT limit, and pull up HIGH when the temperature is below the hysteresis. The conversion rate specified in the CR[1:0] is...
View ArticleForum Post: RE: AFE5809 Custom board based on EVM
Pavel,1. The CDCM7005 buffer is used only for the CW circuit, so you will not require it for TGC mode.2. Yes, this can be floated if not used.3. Yes, these are generated internally. Please decouple...
View ArticleForum Post: RE: LMT84-7 Eval Board layout
Hi Jonathan,I will get back to you soon.Aaron
View ArticleForum Post: RE: AFE5809 SPI
Hello Jack,We have received your inquiry regarding the SPI interface of the AFE5809EVM and hope to have some answers back to you shortly.RegardsPraveen.
View ArticleClik here to view.
Forum Post: RE: LM98714 Initialization code
Hi Govind,I've attached a register map for the LM98714 (but I don't have any details for the conditions / settings to share with you).(Please visit the site to view this file)You may have mis-typed the...
View ArticleForum Post: difference between TMP432A and B vesion
what difference is between TMP432A and B?
View ArticleForum Post: RE: TMP 006 distance between sensitive area and front window
Hi,Thank you you for your inquiry. TI regards such detailed construction information as proprietary and as such it cannot be shared outside of TI. There are mechanical dimensions in the product data...
View ArticleForum Post: RE: AFE5809 SPI
Hi,The SPI Data matches the data as displayed on the AFE5809 EVM GUI.The SCLK is running only at 128 KHz.Thanks,Jack
View ArticleForum Post: RE: difference between TMP432A and B vesion
Hi Longchang,As Abhi mentioned the difference is the two-wire address. The address of the TMP432A is 4Ch (1001100b). The address of the TMP432B is 4Dh (1001101b). You can find a little bit of...
View ArticleForum Post: RE: LM98714 Initialization code
Hi Hooman HashemiThanks for your feedback..My INCLk is 50Khz only ,in the above table for INCLK = ADCLK minium clock is 5MHzbut for INCLK = PIXCLK minium clock is mentioned in the table.and the...
View ArticleForum Post: RE: LM98714 Initialization code
Hi Govind,As you have noted, the LM98714 would not work with INCLK of 50kHz. May be you can explain what you are trying to do and what dictates your low INCLK frequency and we will get back to you with...
View ArticleForum Post: RE: ADS7846 ADC VALUES NOT CORRECT
Hi John,First, if your customer is starting a new design based on ADS7846, I would recommend that your customer use TSC2046E instead of ADS7846. The TSC2046E is the next-generation version of the...
View ArticleClik here to view.
Forum Post: RE: AFE5809 SPI
Hi Jack,According to your using AFE5809EVM and controlling SPI using different test board.We tested AFE5809EVM and measured the EVM converting USB bus to 8-pin data to control SPI and other...
View ArticleForum Post: Why does TI LM57 analog temp sensor(connected to MSP430 ADC) have...
Hi EveryoneI have a strange issue with using the TI MSP430F5310 ADC and the TI LM57 temp sensor. the Rsense values are at 46.4k and 499.9k for Rsense1/Rsense2. The issue is that, when my...
View Article