Forum Post: RE: GUI for the DRV2700EVM
Hi Corey, You can find the Piezo Control Console in the DRV2700EVM product page, under Development Tools. Regards, Leo Rodriguez
View ArticleForum Post: RE: GUI for the DRV2700EVM
The Piezo control Console will not open on my computer. Every time I launch the program I get a message saying" PiezoControlConsole has stopped working." and it will not launch. I can send a screenshot...
View ArticleForum Post: RE: DRV2605LYZFT - Unable to drive vibration motor
Hi, Kastoori: Yes, we can do that. here are the steps: set DRV2605L to ERM mode and ERM open loop set the wanted output voltage to register 0x17 set RTP mode and RTP strength
View ArticleForum Post: RE: GUI for the DRV2700EVM
Hi, Corey: it is the GUI we are talking about. may i know what OS is runing on your computer? it suppose to run on the Windows 7. can you please show me the error message shown when the launch fails?
View ArticleForum Post: RE: DRV2605LYZFT - Unable to drive vibration motor
Hi, The above mentioned steps (step 1 and step 2 with 0x17 register to 0x88) is configured while loading the device driver itself, if we select the ERM type. But still, i am not able to drive the motor...
View ArticleForum Post: RE: DRV2700EVM GUI Location
Hi, I am having trouble launching the Peizo Control Console application for the DRV2700EVM . I have installed and uninstalled 3 times. I have 2 questions; 1. In the product documentation it tells me to...
View ArticleForum Post: DRV2667 - recommended piezo bender
Do we have a recommendation (current) for a piezo actuators for the DRV2667 ? The links to previous e2e recommendations are no longer working. Avnet does not seem to carry the SAMSUNG device called out...
View ArticleForum Post: DRV2700EVM GUI launch issues
Hi I am trying to control the setting on a DRV2700EVM board. The product documentation tells me that I need to download the GUI to change the settings and enable the output voltage. When I click the...
View ArticleForum Post: RE: DRV2667 - recommended piezo bender
Here is a list of some piezo vendors. We will be updating the list next week because a few vendors have changed. MPlus has taken over the Samsung actuator business and they should have some similar...
View ArticleForum Post: RE: DRV2700EVM GUI launch issues
Hi Corey, I just ran through the installation and it worked fine on my Windows 7 machine. I have tested this software out on more than one computer and never had a problem. Yes, Piezo Control Console...
View ArticleForum Post: Setting t_(SAMPLE_TIME) in DRV2605 for haptics/LRA application
We are using the DRV2605 in RTP (8 bits unsigned), closed-loop mode unidirectional, to drive LRAs. This is the first time that we are using the DRV2605 . The datasheet is quite extensive and clear,...
View ArticleForum Post: RE: Connecting 4 3-wire RTD sensors in one ADS1248
Dear Vincenzo, I would like to thank you once more for your support! We would like to use 2 pH sensors and four 3-wire RTD's. For this reason we are focusing in using 2 ADS1248 for each pH sensor and...
View ArticleForum Post: RE: DRV2700EVM GUI launch issues
Hi, Corey: can you please share some "Detail"? it will help a lot. Many thanks.
View ArticleForum Post: RE: DRV2605LYZFT - Unable to drive vibration motor
Hi, Kastoori: can you please share the register dumps? we can check from the register configurations. Thanks.
View ArticleForum Post: DRV2065EVM firmware issue
I am using the DRV2605 EVM for my project, I followed the guide on TI's website using a MSP430 launchpad to reprogram the evaluation kit. But somehow I wanna reset the kit by its original firmware, so...
View ArticleForum Post: RE: DRV2605LYZFT - Unable to drive vibration motor
Hi, Please find the register dump( Registers 0x0-0x22) below in calibration mode. 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: ec 07 00 01 01 00 00 00 00 00 00 00 00 00 00 00 10: 00 05 19 64 19 ff 88 88 0c 6c...
View ArticleForum Post: RE: DRV2065EVM firmware issue
Hi Run, Are you able to connect the EVM to Haptics Control Console? You can update the firmware in Help -> Firmware Update. Follow the instructions on screen and let us know how it goes. EDIT: You...
View ArticleForum Post: RE: DRV2065EVM firmware issue
Hi, Yu: i think you don't build the firmware correctly. there are no other way except reprogramming the board with MSP430 programmer.
View ArticleForum Post: RE: Setting t_(SAMPLE_TIME) in DRV2605 for haptics/LRA application
Hi Hong, Your post is being moved to the Haptics forum for better support.
View ArticleForum Post: RE: DRV2065EVM firmware issue
Hi Leo, Thanks for your reply. I currently do not have the DRV-USBCOM-EVM board. I did try the same thing simply through the MSP430G2553 launchpad (SBW) to the EVM and the console, it did not work. So...
View Article