Forum Post: RE: LM95701 accuracy error
Hi,As I was started to be involve in the issue I discussed here I want to see the number my self still I can see different between sensors which exhibit the same conditions but still I did not see...
View ArticleForum Post: RE: TMP435 giving wrong result LSI requesting negativ supply bias...
Hi Abhi, thanks for your response. If you talk about leackage on diode B I do not think this will have an impact. To my understanding the temperature is measured via the voltage drop of diode A with...
View ArticleForum Post: RE: TMP100/TMP101 I2C clock stretching
No, TMP100/TMP101 does NOT have SCL clock stretching implemented in the design.Regards,Abhi
View ArticleClik here to view.
Forum Post: Inquiry regarding Power-Up/Reset Format on TMP102
Hello, allNow we have one inquiry regarding Power-Up/Reset Format on TMP102 from our customer.Please refer to the item below, and feedback us with your comment.When referring page 7 CONFIGURATION...
View ArticleForum Post: AFE4300 Clock Source
For 1Mhz clock source, please let me know whether we can use the maxim part MAX7375AXR105. The AFE4300 dont have pin capacitance value on datasheet and the MAXIM device performs better on 10pF load
View ArticleForum Post: RE: LM2917M - Pin out
Amplitude : -1V to +4VFrequency Range : Since I am using frequency generator, I tried from 1Hz to 1MHzInput Signal Type : I tried for both Sine Wave & Square WaveVCC_A : 8 V
View ArticleForum Post: LMP91200 no change in VOUT
Hi,We are interfacing STM32 with LMP91200 via SPIUsing SPI driver we could configure the LMP91200, once we write the new value, we can read the old value of LMP91200.Configuring pHWrite data: 0080 Read...
View ArticleForum Post: RE: LM2917M - Pin out
Hello Donald,Tons of Thanks for your support. Circuit is up & running.
View ArticleForum Post: How can I make a skin temprature monitor for children？
Hello，we are planning to make a body temperature monitor for childs,based on cc2540/1,and send the result to mobile.that meanswe want the accuracy should be +/- 0.03 degree on a range of 35~50...
View ArticleForum Post: RE: Driver of Windows Touch
Hi Alpha,Could you tell me which windows you are referring to? Windows CE, Windows Mobile or Windows Phone?Andy
View ArticleForum Post: RE: wrong data from TSC2046 Touch point
Hi Jin,Are you evalating the TSC2046 EVM from TI now? Could you tell me more about the incorrect coordinates you found? Do this happen when you press the touch panel with light pressure? If you press...
View ArticleForum Post: RE: TSC2004 PENIRQ Problem
Hi Nizar,Have you tried the Linux driver which you can download from TI yet? Here is link to th driver : http://www.ti.com/tool/tsc2004-linux-drv Andy
View ArticleForum Post: Linux Kernel 3.0 Driver for LM92
Hello all,did we have a Linux Kernel 3.0 Driver for our LM92.Best regardsOlaf
View ArticleClik here to view.
Forum Post: RE: Inquiry regarding Power-Up/Reset Format on TMP102
Abhishek-san,Thank you for your continuous support towards the inquiries from our customer.I have some additional inquiries regarding configuration register and temperature register individually....
View ArticleForum Post: RE: Urgent: need TSC2017 driver!
Dear Andy,I am following your suggestions and now investigating possible circuit problems. Paul
View ArticleForum Post: RE: AFE5808 Clock Input
the LVDS voltage depends on driving current vs termination R. in past TI ADCs, we assume +/-3.5mA @ 100ohm load. it appears to be 0.7Vpp. when driving current is reduced, LVDS votlage is reduced as...
View ArticleForum Post: TS3V330 switch and the variablility of the On/Off times between...
Dear AllI need to quickly switch “On” and “Off” a predefined DC level but to do that in four channels synchronously. The TS3V330 video switch seems to satisfy the requirements:About 2ns rising/falling...
View ArticleForum Post: RE: TMP006
Hello Bill,Lens is the only option when you are targeting 30-40cm distances from an object that's 2-5cm wide. SNR depends upon how good of an optics setup you can achieve. When you mentioned "close...
View ArticleForum Post: RE: TSC2046 noise issues
Hi Andy,Thank you for feedback. The 1nF capacitors and digital average filtering was a good compromise between noise and speed; 10nF was too slow. Gabi
View ArticleForum Post: RE: The question about LM98620
Hello Mr.HoomanThank you for quick reply!I understood that you wrote.Best Regards.Taichi
View Article